assuming this is a 12 volt system....45 amps.
The Full load current of that amp is approx. 17A, but you base you fuse size between the Full load current of your load and the current carrying capacity of the supply cable, if the size or the CCC of the cable is unknown, I would recommend sticking as close to the FLC as possible
The value of a Crunch 200 watt amp can vary depending on its condition, age, and market demand. On average, a used Crunch 200 watt amp in good working condition might sell for around $50 to $100, but prices can fluctuate.
For a 1500 watt block heater, you would typically use a 15 amp fuse. This is calculated by dividing the watts (1500) by the voltage (120 in most cases) to get the amperage. In this case, 1500 watts / 120 volts = 12.5 amps, so a 15 amp fuse would be the appropriate size to accommodate any potential spikes in power usage.
Fuses or breakers are used to protect the conductor to the load. A #14 wire conductor is rated for 15 amps. Most home circuitry is done with #14 wire. The minimum size breaker in an electrical panel is 15 amp so it looks like a 15 amp fuse or breaker can be used for a 100 watt light bulb.
Yes it should be all right. Ratings for amp/speakers are approximate but as a rule it is preferable for the speaker to be rated higher than the amp.
The Full load current of that amp is approx. 17A, but you base you fuse size between the Full load current of your load and the current carrying capacity of the supply cable, if the size or the CCC of the cable is unknown, I would recommend sticking as close to the FLC as possible
10 amp will do and be safe.
The equation that you need to use is I = W/E. Amps = Watts/Volts. As you can see there is no voltage stated but when you obtain the voltage value use it in the equation.
Yes I do not see why not as long as the in line fuse does not exceed the power the amp is pulling. You want the fuse to blow instead of the amp so you need a fuse that can only handle 1600 watts or the equivalent to....
The value of a Crunch 200 watt amp can vary depending on its condition, age, and market demand. On average, a used Crunch 200 watt amp in good working condition might sell for around $50 to $100, but prices can fluctuate.
For a 1500 watt block heater, you would typically use a 15 amp fuse. This is calculated by dividing the watts (1500) by the voltage (120 in most cases) to get the amperage. In this case, 1500 watts / 120 volts = 12.5 amps, so a 15 amp fuse would be the appropriate size to accommodate any potential spikes in power usage.
Fuses or breakers are used to protect the conductor to the load. A #14 wire conductor is rated for 15 amps. Most home circuitry is done with #14 wire. The minimum size breaker in an electrical panel is 15 amp so it looks like a 15 amp fuse or breaker can be used for a 100 watt light bulb.
It will draw over 18 amps and will blow a 15 amp fuse.
fuse is under the hood by passenger side in fuse box labled as amp is a 25 watt fuse...there is another by passenger door in the vehicle also labled amp
The recommended conduit size for a 200 amp service is typically 2 inches in diameter.
7.2kW shower = 32 Amp fuse = 6 mm2 cable size7.5kW shower = 40 Amp fuse = 10 mm2 cable size8.5kW shower = 40 Amp fuse = 10 mm2 cable size9.5kW shower = 40/45 Amp fuse = 10 mm2 cable size10.5kW shower = 45 Amp fuse = 16mm2 cable size
20 amp a 20 amp fuse