0
Wire sizing is based on the amperage of the load. Without this amperage the wire size can not be calculated. Also with sub panels it should be stated whether it is under the same roof as the main panel or separate from the main building. Different code rules apply to each application.
What else can I help you with?
What size wire should be used from service to 100 amp breaker panel?
A 2-gauge copper wire is typically used for a 100 amp service with a maximum distance of 100 feet. For longer distances, a 1-gauge copper wire may be needed. It is important to consult local electrical codes and a qualified electrician for the most accurate sizing based on specific requirements.
Size wire is needed to run a 125 amp panel?
For a 125 amp panel, you would typically use #1 AWG copper wire or #2 AWG aluminum wire for the main service entrance conductors. It's important to consult local electrical codes and a qualified electrician to ensure the correct wire size for your specific situation.
What is the difference between 1-0 wire and number 1 wire?
1-0 or 1/0 actually means one zero and is thus pronounced "won aught". In the US, wire is sized per American Wire Gauge or AWG which gets larger as the gauge size gets smaller. 1 AWG wire is pretty big wire (about 1/4" in diameter). 1/0 or "0" AWG wire is a bit larger. By contrast, 4/0 (0000) AWG wire is about 1/2" in diameter). The larger the wire, the higher the current carrying capacity. AWG, Ampere Rating, Some Uses 1, 130, Small House Service 0, 150, 40 HP Motor 0000, 230, Large House Service
On a 110V circut wire what is the voltage of the hot wire?
The voltage (AC RMS) between the "hot" wire and the "neutral" wire is 110 VAC (volts alternating current). But it should be noted that the "110" volts supplied to homes can range from 95 to 130 volts, with the present standard now being 120 VAC. In addition, if the circuits are wired in accordance to most local codes, the "neutral' wire is connected to the "ground" wire in the distribution (fuse or circuit breaker panel or box), so the 110 volts will also appear between the "hot" wire (black color coded wire) ,and the ground wire (bare wire, within an insulating jacket carrying the insulated "hot" and "neutral" wires). Note, however, that the "ground" wire is not designed nor intended to carry the "return" current from the "hot" wire, but only as a safety "ground" for currents due to shorted or improperly wired devices connected to the circuit.
How many gallon of tea for 130 people?
To determine how many gallons of tea you'll need for 130 people, a common guideline is to serve about half a gallon per person for a gathering. Therefore, for 130 people, you would need approximately 65 gallons of tea. Adjust based on the duration of the event and whether other beverages are also being served.
You want to write a algebraic expression on every roll there is 130 feet of wire you need 65 feet of wire per board how many rolls of wire would you need for 12 boards?
12*65/130
Size wire for running 240v 130 amps mig welder?
5 mm
What size cable for 125 amp sub panel?
A #2 copper conductor with an insulation factor of 90 degrees C is rated at 130 amps.
What gauge wire do you need for 220v 100a power?
I would recommend 1/0 just to be sure you have very little line loss. <<>> It depends on whether the 100 amp panel is rated at 100% or 80% loading. If the panel is only rated for 100% loading, meaning that a full 100 amps can be drawn from it, the wire size will be #2 copper conductor which is rated at 130 amps. The feeder can only be loaded to 80 present so will have a working amperage of 130 x .8 = 104 amps. If the panel is only rated at 80 percent loading then a #3 copper conductor can be used. A #3 copper conductor with an insulation factor of 90 degrees C is rated at 115 amps. 115 x .8 = 92 amps.
What size wire should be used from service to 100 amp breaker panel?
A 2-gauge copper wire is typically used for a 100 amp service with a maximum distance of 100 feet. For longer distances, a 1-gauge copper wire may be needed. It is important to consult local electrical codes and a qualified electrician for the most accurate sizing based on specific requirements.
Size wire is needed to run a 125 amp panel?
For a 125 amp panel, you would typically use #1 AWG copper wire or #2 AWG aluminum wire for the main service entrance conductors. It's important to consult local electrical codes and a qualified electrician to ensure the correct wire size for your specific situation.
What is the hair color of the mistress in sonnet 130?
black wire
What tire size is the same as mt90B16 a 100 120 or 130?
130/90 16 is the conversion size for the front tire
What size wire would you use to wire a motor that draws 16 amps from a circuit?
AWG Wire Ampacity Gage (Amperes) 16 10 A 14 15 A 12 20 A 10 30 A 8 45 A 6 65 A 4 85 A 2 115 A 1 130 A 0 150 A So if anything its probably 12-14 gauge wire Yw
Is it good to be 130 pounds and wear a size 3?
A size three would be too small for someone of 130 lbs. It also would reveal any fat that you have and all its bumps and creases.
What skateboard size should i get my foot size is 10 US and i weigh 130 pounds?
You should get a 7.75x3.15
What wire gage for 130' supply 100 amp service?
I would run 1/0 gauge.
