0
What else can I help you with?
What tools will you need to replace a valve cover gasket on a 1993 mercury topaz?
To replace a valve cover gasket on a 1993 Mercury Topaz, you will need basic hand tools such as sockets, wrenches, and a screwdriver. Additionally, it may be helpful to have a torque wrench, gasket scraper, and a new valve cover gasket. It's also a good idea to have some rags or shop towels on hand to clean up any oil spills during the process.
Where is the starter located on a 1988 Mercury Topaz?
The starter on a 1988 Mercury Topaz is typically located on the bottom side of the engine, near the transmission bell housing. It is attached to the engine block and is accessed from underneath the vehicle. It may be necessary to raise the car and remove some components to reach the starter.
Where is the oil drain plug on the 94 topaz?
Actually the drain plug is at the back of the oil pan. It's a stupid design because when you remove the plug the oil shoots straight back toward the rear of the car. Mine will shoot as much as a foot depending on how warm the oil is. So, when you change the oil make sure you have a very wide mouthed catch pan to catch the oil or else it will likely miss the opening. Then as the oil gets closer to completely drained the stream will not be shooting as far and you'll have to adjust the position of your catch pan. Onthebottomoftheoilpan.
Why is there oil in air box on mercury topaz 2.3 liter?
The oil is coming from the breather tube that comes from the valve cover. There is supposed to be a filter that will block this, but alas, they sometimes do not work to well. One way to stop this, if it is a big problem would be to put a little batch of steel wool in the breather line at the air box side. This might help. Or, replace the original line and filter. As long as there is not too much oil getting in there, the car will still run fine.
What causes the ticking noises in 1994 Mercury Topaz when in idle?
Sounds like you are hearing lifter noise. If this engine has solid lifters, then they can be adjusted to remove most of the noise. If it has hydraulic lifters, try pouring one can of Seafoam Cleaner in the crankcase with the oil. Seafoam can be purchased at most auto parts stores. Drive the car for 500 miles and then change the oil & filter. Repeat if necessary. This may or may not help.
Where is the oil pump located on a 1993 Mercury Topaz?
Inside the oil pan, mounted on the engine block.
Where is the oil pan located on a 1988 mercury topaz?
The oil pan is bolted to the bottom of the engine
What weight oil do you used in a 1993 Mercury Topaz?
1w30 in warm weather, 5w30 in cold weather
Where is the oil drain plug on a 1993 Mercury Topaz?
Hi. It is located at the bottom of the oil pan near the back of the oil pan. It is mounted on an angle. It requires a 5/8" or 16 mm wrench to remove. Hope this helps.
Were is the plug for the oil pan on a 1989 mercury topaz?
Its on the bottom of the oil pan.
Where is the oil sending unit located on the engine of a 4 cylinder of a 1993 mercury capri?
it is just above oil filter to the left
What kind of oil does a 1990 mercury topaz use?
5 W 30 on a 2.3 Liter.
How many quarts of oil does a 92 mercury topaz take?
# 2.3Liter engine takes 5.0L of oil # 3.0Liter engine takes 4.5L of oil
Location of oil pressure switch 2.0 l engine for 1994 Mercury Topaz?
Should be around the oil filter, check the manual if not there.
How much engine oil does 1993 mercury capri hold?
A 1993 Mercury Capri (with the 1.6 4 cylinder DOHC engine) requires 3.2 quarts of oil.
Where is the oil drain plug on a 1993 mercury villager?
The oil drain plug is located on the lower right side of the oil pan. You can easily get to the oil drain plug and oil filter by removing the right front wheel.
What kind of oil do you put in a 1992 Mercury topaz?
10w30 would be a good choice. Any major brand is fine.
