0
Why does the voltage on every other breaker in your box read 104 volts while the other breakers read 124 volts?
You may not have a good connection one your "neutral" wire, somewhere between the breaker panel and the transformer.
Note that the neutral wire is the center of the 240 V feed, and if the connection is inadequate, dirty, oxidized... you may experience some neutral "float".
Make certain that the center feed of the breaker panel is tightened, and beyond that, there isn't much that YOU can do; you'll need to contact the local electric service provider.
Just a warning here...
if you haven't worked with live circuits before and REALLY know what you're doing, make certain that you shut off the power at the meter base before you attempt to do anything to the inside of the breaker panel. An open breaker panel exposes you and anyone else nearby to a very real and deadly potential for electrocution.
What else can I help you with?
Why would the voltage drop to 105 in one outlet in your old mobile home?
Check the voltages on the other receptacles in the home. If you find other lower voltages go back and shut that breaker off. Go through out the house shutting off the breakers that have low voltage on them. If other ones are lower see if you can establish if the voltage drop is on the same bus breakers. These will be every alternate breaker. If the breakers that you shut off are every other breaker then the problem is with the incoming utility supply. Give them a call and get them to read the voltage at the meter base. If you can not find any other low voltages in the home then shut the breaker off to that circuit and change the receptacle out for a new one. If the voltage is still low after replacing the receptacle, it could be the breaker that is feeding that circuit.
Do you have a circuit breaker which operates for one millon volts?
Circuit breakers are typically designed for lower voltages, such as up to 1000 volts. For extremely high voltages like one million volts, special high-voltage circuit breakers or other protection devices would be used in power systems. These specialized devices are designed to handle the unique challenges posed by very high voltage levels.
Can you install a 2 20 breaker into a breaker box that has space but all other breakers add up to more amps than the 200 amp main breaker?
No, you cannot install a 2x20 amp breaker if the total amperage of all the breakers exceeds the main breaker rating, as this would overload the system. The total amperage of the breakers should not exceed the main breaker rating to ensure safe operation of the electrical system.
Can you install a tandem breaker?
Tandem breakers, often called split breakers or double breakers, provide two separate circuits in the space of a regular sized breaker opening. Every circuit breaker panel has a limited number of circuit openings available. The problem is that when the openings are all used up and you still need to add another circuit, what do you do? You could change the electrical panel or double up circuits on a breaker, but this could place too much load on a particular circuit. So what then? The answer that many have found is a tandem breaker. This type breaker is the same size as any other breaker, but it has its difference. This breaker sports two smaller breakers built into one regular sized breaker. Each has its own breaker switch and the breaker snaps in just like a regular breaker. With this simple innovation, you can add a circuit and protect the circuit on its own dedicated line.
Can you use a 220 breaker in place of 110 breaker on 110 service?
Answer for USA, Canada and countries running a 60 Hz supply service.Breakers are rated in amperage and by the amount of poles that they have. Your classification of a 220 breaker is described in electrical terminology as a two pole breaker.Choosing the amperage of the two pole breaker depends upon the 220 volt load that it feeds.Two pole breakers for 220 volt loads.Single pole breakers for 120 volt loads.If the service is only 120 volt then every other bus bar in the panel will be energized. If the panel is a 120/240, then every bus bar in the panel will be energized.This is how and why a 240 volt load requires a two pole breaker.To the answer, yes you an use a two pole breaker in a 120 volt service but only one side of the breaker will have voltage on it depending on where it is situated in the panel board.
Why would the voltage drop to 105 in one outlet in your old mobile home?
Check the voltages on the other receptacles in the home. If you find other lower voltages go back and shut that breaker off. Go through out the house shutting off the breakers that have low voltage on them. If other ones are lower see if you can establish if the voltage drop is on the same bus breakers. These will be every alternate breaker. If the breakers that you shut off are every other breaker then the problem is with the incoming utility supply. Give them a call and get them to read the voltage at the meter base. If you can not find any other low voltages in the home then shut the breaker off to that circuit and change the receptacle out for a new one. If the voltage is still low after replacing the receptacle, it could be the breaker that is feeding that circuit.
Why do you need to know voltage of a breaker?
Breakers and other electrical equipment are rated in voltage so you know what voltage they can withstand. The breaker could fail and start a fire if you apply a higher voltage than it is rated for. Breakers are actually rated in amps (current in excess of this will trip it), interrupting rating (how many amps the breaker can handle during a short circuit) and in volts (is the difference of potential or the pressure that is pushing the current). The breaker I am looking at is rated for 15 amps, 10,000 amps interrupting rating and 120/240 volts.
Is there a difference between 480volt 30 amp breaker and 208volt 30 amp breaker?
Yes, all breakers have an insulation factor as to the maximum amount of voltage the device can be subjected to. A 208 volt breaker has a maximum up to and including 240 volts. A 480 volt breaker has a maximum up to and including 600 volts. A higher voltage rating breaker can be used on lower voltages but not the other way around.
Do you have a circuit breaker which operates for one millon volts?
Circuit breakers are typically designed for lower voltages, such as up to 1000 volts. For extremely high voltages like one million volts, special high-voltage circuit breakers or other protection devices would be used in power systems. These specialized devices are designed to handle the unique challenges posed by very high voltage levels.
Can you install a 2 20 breaker into a breaker box that has space but all other breakers add up to more amps than the 200 amp main breaker?
No, you cannot install a 2x20 amp breaker if the total amperage of all the breakers exceeds the main breaker rating, as this would overload the system. The total amperage of the breakers should not exceed the main breaker rating to ensure safe operation of the electrical system.
Can you install a tandem breaker?
Tandem breakers, often called split breakers or double breakers, provide two separate circuits in the space of a regular sized breaker opening. Every circuit breaker panel has a limited number of circuit openings available. The problem is that when the openings are all used up and you still need to add another circuit, what do you do? You could change the electrical panel or double up circuits on a breaker, but this could place too much load on a particular circuit. So what then? The answer that many have found is a tandem breaker. This type breaker is the same size as any other breaker, but it has its difference. This breaker sports two smaller breakers built into one regular sized breaker. Each has its own breaker switch and the breaker snaps in just like a regular breaker. With this simple innovation, you can add a circuit and protect the circuit on its own dedicated line.
What are the options available for challenger breakers replacement?
The options available for replacing challenger breakers include purchasing new breakers from the same manufacturer, using compatible breakers from other brands, or upgrading to a newer breaker panel system.
Can you use a 220 breaker in place of 110 breaker on 110 service?
Answer for USA, Canada and countries running a 60 Hz supply service.Breakers are rated in amperage and by the amount of poles that they have. Your classification of a 220 breaker is described in electrical terminology as a two pole breaker.Choosing the amperage of the two pole breaker depends upon the 220 volt load that it feeds.Two pole breakers for 220 volt loads.Single pole breakers for 120 volt loads.If the service is only 120 volt then every other bus bar in the panel will be energized. If the panel is a 120/240, then every bus bar in the panel will be energized.This is how and why a 240 volt load requires a two pole breaker.To the answer, yes you an use a two pole breaker in a 120 volt service but only one side of the breaker will have voltage on it depending on where it is situated in the panel board.
What breaker boxes are compatible with GE circuit breakers?
GE circuit breakers with catalog numbers ranging from THQL1115 through to THQL1150 can be substituted like for like with Cutler-Hammer circuit breakers coded CL115 through to CL150, ITE Siemens circuit breakers coded Q115 through to Q150 and Square D circuit breakers coded HOM115 through to HOM150. These are single pole breakers. GE circuit breakers with catalog codes from THQL2115 through to THQL2150 can be substituted with Cutler-Hammer circuit breakers CL215 through to CL250, Square D circuit breakers HOM215 through to HOM250 and ITE Siemens circuit breakers Q215 through to Q250 of the same amperage and voltage. These are double pole breakers.
Will a 100 amp breaker box work if there are 5 220 amp breakers and 7 110 breakers?
It will if the 100 amp distribution board is a 20 circuit board. Ten spaces for the 240 volt breakers and seven spaces for the 120 volt breakers. There are two types of 100 amp breaker boards, one rated at 100 percent and the other at 80 percent. Depending on what rating on the panel board you are using will govern the maximum amount of current that can be legally drawn from the board. This breaker board rating will also govern the size of the main breaker installed and the wire size to feed the board, either 100 amp wire or 80 amp wire. The second consideration is what are the connected loads to the breakers, with the total of seventeen breakers, the board can only supply as much amperage as the main breaker will allow.
Why am I only getting 120 volts from a 30 amp breaker that should be feeding 220 volts?
I assume you have a 30 amp two pole 220 volts breaker. Check the voltage source. If the source voltage is 220V, but out let voltage is 120 then the breaker must be faulty, a high resistance or partial open circuit could have caused the reduced voltage at the breaker outlet.
How would you be able to change the trip of a circuit breaker?
Small size home breakers have a fixed setting and can not be adjusted. Three phase moulded case breakers have adjustable trip settings on the load side of the breaker. These overloads can be set for motor inrush to stop the breaker from needless tripping and yet still protect the other equipment down stream from the breaker.
