0
What else can I help you with?
Need of isolator on both side of circuit breaker?
Before anyone is allowed to work on a high-voltage circuit breaker, it must be tripped, electrically isolated, earthed (grounded), barriers/warning notices put in place, and a permit to work document issued by an engineer to the senior member of the maintenance crew. 'Isolation' means a physical (and visible) break in the conductors between the circuit breaker and any potential source of supply -and this is provided by placing isolator switches on each side of the circuit breaker. Without these isolators, the circuit breaker would remain energized, even though the circuit has been broken by the circuit breaker.
Does the current still flow when the circuit has blown?
If everything is working as it should then no current flows when the breaker is off. This is no better example of this than there is on answers. When a do it yourselfer looks for an answer and gets one, the answer is always ended with the suggestion that before doing any work always shut off the breaker. If the breaker is malfunctioning one symptom is that a voltage is still present even though the handle is in the off position. If this is the case change the breaker out immediately.
Can you get electrocuted if the switch is off but the breaker is on?
Yes you can. The proper wiring of a switch is to bring the hot wire to the top of the switch terminal and connect the load to the bottom of the switch. When the breaker is turned off it disconnects the voltage from the top of the switch and the switch is then safe to work on. By not turning the breaker off, the voltage is present at the top of the switch which could subject you to a nasty shock if you come into contact with it.
Can you use a 25 amp double pole breaker for a 240 heavy duty whirlpool dryer.?
The recommended breaker for dryers is 30 amps. If you want to do the calculation to see if a 25 amp breaker will work use the following formula. W = A x V, A = W/V. Find the wattage of the unit and divide it by 240 volts to get the amperage. If the amperage is under 25 amps then the breaker will work. If the amperage is over 25 amps then a 30 amp breaker on #10 wire will be needed.
Does a shunt trip breaker work from a dry set of contacts?
Yes, but you need a power source, for the shunt trip coil voltage, in the circuit.
Will a siemens breaker work in a GE panel?
Possibly. Depends on which model Siemens breaker you have.
Electricity generation using speed breaker working?
how to work a project on speed breaker energy
WILL sink work without the vacuum breaker?
Yes.
Need of isolator on both side of circuit breaker?
Before anyone is allowed to work on a high-voltage circuit breaker, it must be tripped, electrically isolated, earthed (grounded), barriers/warning notices put in place, and a permit to work document issued by an engineer to the senior member of the maintenance crew. 'Isolation' means a physical (and visible) break in the conductors between the circuit breaker and any potential source of supply -and this is provided by placing isolator switches on each side of the circuit breaker. Without these isolators, the circuit breaker would remain energized, even though the circuit has been broken by the circuit breaker.
How do you check a breaker in a mobile home?
The breaker panels are exactly the same as ones in regular houses. To re-set a breaker, you turn it fully OFF, then to fully ON and it should work.
Will cutler hammer breaker panel fit a GE breaker?
No, a Cutler Hammer will not work in a GE panel or vice versa.
How can a circuit breaker be made to work after it has opened?
put your dick in it
How do you work air circuit breaker?
There are various to check if your air circuit breaker working. You can use various tools that are available to test your air circuit breaker. A clamping ammeter is ideal for this purpose.
Did my dryer trip the breaker or vice versa when I turned the breaker back on but now the dryer won't work?
The dryer tripped the breaker. Have it repaired. Don't try to use it again. You could cause a fire.
How can I replace outlets in my home?
To replace outlets in your home, first turn off the power to the outlet at the circuit breaker. Remove the cover plate and unscrew the outlet from the electrical box. Disconnect the wires from the old outlet and connect them to the new outlet, following the same configuration. Secure the new outlet in place and replace the cover plate. Turn the power back on at the circuit breaker and test the outlet to ensure it is working properly. If you are unsure or uncomfortable with electrical work, it is best to hire a professional electrician.
Will a weak circut breaker cause a water heater not to work?
Yes
What is the fabricated plate work industry?
The fabricated plate work industry is comprised of large and small manufacturing facilities.
