answersLogoWhite

0


Best Answer

Most brackets today come with all possible bolt sizes for your range of TV sizes. It will be either a 6mm or 8mm bolt. Just try the bolts from the hardware pack when you buy your bracket.

User Avatar

Wiki User

12y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What size scres to mount toshiba model 37hl67s to wall mount?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Performing Arts
Related questions

How do you remove the gas tank on a 94 silverado to change the fuel pump?

take the bed off! remove the scres around the fuel filler neck and remove the bolts holding the bed on the frame. There are only like 6 or 10 depending on model year i think. Lift off with a friend and do it that way, its way easier :)


How do you install a headlight for 1995 Pontiac Sunfire?

remove the plastic shield and unbolt two scres and the entire lens comes out don't touch the glass of the new bulb


How do you adjust the headlights on a 1999 Toyota Toyota Camry?

There are two scres on each headlight assy. One controls the upwards and downwards motion, and the other controls left to right movement


Where is the cabin filter on an 2004 suburban?

Your filter should come with instructions. It is located under the passangers side dash. you undo a few scres, slide the old ones out and put it back together


How do you replace the gear selector lamp on a Volvo 940?

unscrew the two hex scres in the middle of the consoule take off the ashtray and cover for the fuses there will be a clip get a small screwdriver to pry the clip off and then you can remvoe the panle and there will be a small bulb that you can replace under the shifter


1996 Honda accord headlight adjustment?

normally done by a switch located on the dashboard. To manually realign disproportionate head lights you need to face the car toward a wall and aligh the beams manually by adjusting the clibs and scres holding head light chasis in place


Where is the fuel filter on a 1991 Mercedes 190e?

under the underbelly of car towards the back on drivers side there is a compartment areaunscrew the wing nuts or scres that hold the platic compartment door and youll see 3 or 4 componenets the fuel pump 1 or 2 of them the accumulator and the fuel filter


360 ford motor how many rounds are they to be set how to adjust a 2 bbl carb where it will start and idle right?

turn mixture screws all the way in till seated. do not overtighten back both scres out 3 and quarter turns. start at that point then fine tune with engine running


How do you disarm the airbag on a 94 camaro and remove the steering wheel?

simply pull tha airbag fuse. remove the 4 torx head scres behind the airbag and remove airbag. unplug theelectrical connector. remove the big nut holding the steering whell. use a puller to remove the steering wheel.


How do you remove radio from 88 caprice?

well its complicated you have to remove the glove box and disconnect the cable that controls the hot/cold setting on the controls then you have to remove all the scres holdin face plate on some are underneath so you have to take out the ash tray to get to them make shure you take off all the knobs for climate control and the radio then disconnect everything you need to so you can work on the faceplate


How do you replace the front speakers in a Saturn 2001 L200?

You will need a Phillips head screw driver and a universal window crank removing tool. unscrew the scres at the bottom of the door panel. and pop of the tweeter grill there is a screw there and one behind a plastic piece where the window switch would be. take off the door panel. and the rest is just to remove the speaker. get a nice carbide drill bid for you will need to make new speaker mounting hole in the door.


How do you replace ignition switch on 96 Volkswagen Passat?

take off the covers at the bottom of the dash. on the left side of the steering wheel you will see a circular pink and black thing with loads of wires. this will pull out with a small bit of force. the ignition switch is what this was plugged into. you will see 2 small screws with red plastic on the faces of them. undo these two screws then pull out the switch just like you did with the other thing. put in the new switch replace the two scres plug the wires back in and reattatch the dash.!!