0
Usain Bolt's running speed is faster than the horsepower of a car engine. Bolt can reach speeds of over 27 miles per hour, while the average car engine produces around 200 horsepower. Bolt's speed is a result of his exceptional athletic ability, while a car engine's horsepower is a measure of its power output.
What else can I help you with?
What causes stator on a 2010 harley to move back and forth?
A common cause for the stator to move back and forth on a Harley is worn stator mounting bolts. These bolts can become loose over time due to vibration and engine movement. It is important to check and properly tighten the mounting bolts to prevent further shifting of the stator.
How much does 3.0kg bag of bolts weigh?
A 3.0kg bag of bolts weighs 3.0 kilograms.
How much does a 3.0-kg bag of bolts weigh?
A 3.0-kg bag of bolts weighs 3.0 kilograms.
Why does fridge make a knocking noise when running?
A knocking noise from the fridge when running can be caused by a few reasons such as the compressor mounting bolts being loose, the condenser fan hitting something, or the evaporator fan motor malfunctioning. It's best to have a professional technician inspect and diagnose the issue to determine the exact cause and needed repair.
How do you open the grating in zork 1?
To open the grating in Zork 1, you need to use the wrench to loosen the bolts on the grating. Pull the grating open after removing the bolts with the wrench.
How do you idle up 1995 eagle talon 5 speed?
theres a idle control on the trottle body. theres two 10mm bolts to loosen and move the cable to idle higher. then tighten the bolts..... do this with the engine running.
Why is the engine shaking?
If you had any recent engine work, ask them to check out your mounting bolts. You should always get new bolts every time. If not, it may be your RPM's are running a little low at idle. You can take it to any automotive garage and have a new idle programed and an oil change should do.
Can you run a02 kia spectra 1.8 dohc with only 9 head bolts?
Running a 2002 Kia Spectra 1.8 DOHC engine with only 9 head bolts is not advisable. The engine is designed to operate with a specific number of head bolts for proper clamping force, which ensures a good seal between the cylinder head and the engine block. Operating the engine with missing head bolts could lead to coolant leaks, loss of compression, overheating, and severe engine damage. It's essential to replace any missing bolts and ensure proper torque specifications are met for safe operation.
Where do you hook engine stand on back left of 1996 Chevy Blazer engine?
The engine stand bolts up to where the transmission bolts to the back of the engine.
Where is the PGR valve on a 2001 Chevy Malibu V6?
are you meaning EGR valve. if so it is in front of brake booster, there are 2 bolts and a steel hose running to it. take out the 2 bolts and remove hose. mounted on engine. it is round and has a set of wires running to top of it!! on top back drivers side.
Why does your 1989 Mazda 626 vibrate on the overrun?
This mite mean you have a bad timing problem... there should be 2 adjustment bolts on the distributor in the front of the engine.. losen those slightly when the car is running and slowly turn the distributor clockwise until the engine sounds to be running better
How many bolts hold the transmission to the engine on a 1995 K1500 Z71?
6 bolts hold the transmission to the back of the engine.
Who is famous for running?
the jamacan athlete ussaine bolts
What are Usain Bolts notable skills?
Running quickly.
What is Bolts torque on 407t ade engine?
Conrod bolts
How many bolts in a Dodge Intrepid starter?
Three bolts hold it to the engine.
How many transmission to engine bolts are there on a 1998 suburban 350 vortex?
There are 6 bolts in the bell housing that hold it to the rear of the engine.
