0
What else can I help you with?
What is a fulcrum called on a pulley?
The point on a pulley where it pivots is called the axle or the shaft. It serves as the point of rotation for the pulley system.
How do i remove a pulley from a shaft?
To remove a pulley from a shaft, you first need to loosen any set screws or locking mechanisms securing it in place. You can then use a pulley puller tool or a gear puller to apply force evenly and remove the pulley from the shaft without damaging either component. If the pulley is stuck, applying penetrating oil and gently tapping it with a mallet can help loosen it before attempting removal.
Is an elevator a fixed pulley or a movable pulley?
An elevator typically uses a combination of fixed and movable pulleys. The pulley at the top of the elevator shaft is fixed, while the pulleys attached to the elevator cab are movable. This setup allows for the efficient movement of the elevator cab up and down the shaft.
The simple machine that operates as a ramp that curves around a shaft is a?
pulley
How do you remove a pulley from an electric motor?
To remove the pulley from an electric motor, you typically need to use a pulley puller tool. This tool grips the pulley securely and allows you to apply force to pull it off the motor shaft without causing damage. Follow the manufacturer's instructions for using the pulley puller properly to safely remove the pulley.
What is the proper name of a square key between a pulley and the motor shaft?
It is simply called a key
Installing a pulley and shaft with a square key for a band saw repair. Previous owner deformed the keyway and I'm having trouble getting the pulley back on the shaft with the key installed.?
http://answers.yahoo.com/question/index?qid=20071023141955AAIY1FP
Why is there no woodruff key on crank pulley on 5.3 vortec?
The 5.3 liter Vortec Engine on the 2000 Chevy Silverado has a tapered crank shaft. The crank pulley has no woodruff key, is not indexed and is pressed on.
What holds the power steering pulley in place on a 1996 Chevy Lumina?
the pulley is a press fit on pump shaft. need puller and installation tool to install. JOE
What pulley drives alternator belt What is wrong if this pulley isn't turning?
the pulley on the harmonic balance drives the alternator belt. this is the pulley at the bottom of the engine ,on the front of the crank shaft if this pulley is not turning you have a problem. this means either the key is missing or the crankshaft is broken
How do you remove crank shaft pulley megane?
To remove a crank shaft pulley you need to first jack up the car. Next, remove the bold holding the crack shaft pulley in place and remove the unit. Reverse direction to put the new crank shaft pulley on your car.
How do you take off a crank shaft pulley?
how to get the crank shaft pulley off of a 03 Hyundai elanta GLS
How to check crank shaft pulley?
A video instruction guide on how to check a crank shaft pulley can be seen on YouTube. Just type in "How to check crank shaft pulley", click on Search, then play the first video.
What causes a pulley to wobble?
Things that might cause a pulley to wobble: The pulley is bent. The shaft the pulley is on is bent. The pulley is mounted crooked.
What is a pulley connected to a shaft?
tu madre
What causes clanking on bottom crank shaft pulley to rattle?
its loose tighten the pulley
How do i Press on a pulley to power steering pump?
One easy method is to clean the pulley and pump shaft. Put the pulley in the kitchen oven at about 250 degrees long enough to come up to temperature. Depending on the pulley material, you can go to much higher temperatures. You couldn't get a steel pulley hot enough to hurt it in a kitchen oven. For every degree you increase the temperature of the pulley, the pulley including the shaft hole, gets larger. If possible reduce the temperature of the pump shaft. Use ice or a CO2 fire extinguisher. This makes the shaft smaller. The effect of making the pulley and it's shaft hole larger, and the shaft smaller should place you where the pulley doesn't need to be forced on the shaft Get the pulley and pump close. Dry the pump shaft. Pick up the pulley with hot pads or heavy gloves and simply slide it on the shaft by hand. This should be one swift, smooth motion and done with out stopping. Every time the pulley touches the pump shaft it will lose heat. and the shaft will gain heat until the pulley stops sliding freely. The idea of doing this this way is to avoid forcing any part of the pump shaft and maybe damaging the pump. I once used a charcoal fire and a cast iron dutch oven to install a wheel bearing on my boat trailer while camping. It worked slick.
