answersLogoWhite

0

find the dints that were there before

User Avatar

Wiki User

14y ago

What else can I help you with?

Continue Learning about Physics

Why use a magnet in washing machine?

Magnets are used in washing machines to help remove metal particles (like pins and screws) from the clothes during the washing cycle. This prevents these metal objects from damaging the washing machine or the clothes themselves. The magnet attracts the metal particles and holds them in place, preventing them from circulating back into the wash.


Does a washing machine need a magnet to operate?

The answer is both yes and no.It actually depends on the kind of washing machine in question.The problem is the motion.A washing machine need some kind of an engine or motor in order to move the cloths back and forth. This can of course be done manually.If we rule out manual washing machines, and also only count in electrical ones then these can be made in two different ways.The motor causing the tumbling or the motion in the washing machine can be made with both permanent magnets like NeoDym, or with purely electrical pulses creating strong electromagnetic fields.Most motors in washing machines made today are made without magnets. It is cheaper to make purely electrical motors where the electricity provides the magnetic fields needed. By electronically rotate the magnetic field around the axis, this will force the motion of the motor. It would use less electricity to make the motors with NeoDym magnets but it would also cost more to produce.As a conclusion: We can not make an electrical washing machine that operate without magnetic fields, but magnetic fields does not have to be made by magnets.


Should a top load washing machine drum wobble back and forth at rest?

This is normal for most washing machine designs. The reason is to enable access to spring attachments which allow the barrel/drum to move during cycles when machine is operating. If there was no 'wobble' the building housing your laundry machines would shake apart with the centrifugal forces created.


How do you adjust a belt tension on a washing machine?

Oh, dude, adjusting the belt tension on a washing machine is like trying to tame a wild beast. You gotta loosen the bolt, move the motor, and tighten it back up. It's all about finding that sweet spot where the belt is snug but not too tight. Just don't let the washing machine boss you around, you're in charge here.


How does the agitator work on a washing machine?

the agitator on most washers go back and forth . at least one i know of goes up and down. we will talk about the back and forth.Underneath the tub usually accessable from the back of the machineis a transmission and belt along with other things. when you start the washer it will fill with water . When the correct volume of water is reached a switch is activated that sends power to the timer which in turn routes power to the proper connections needed to agitate. now when washing power is sent to a agitator control which lifts a plunger that makes the transmission rock back and forth which is calledagitation

Related Questions

What is the purpose of the washing machine p trap and how does it contribute to the overall functionality of the washing machine?

The purpose of the washing machine p trap is to prevent sewer gases from entering the washing machine and the home. It also helps to maintain proper drainage by creating a water seal that prevents odors and gases from coming back up the drain. This contributes to the overall functionality of the washing machine by ensuring that it operates efficiently and safely.


What is located at the back of a washing machine?

The back of a washing machine typically houses the motor, belts, and other mechanical components that help it operate.


What it agitation?

Moving back and forth like a washing machine


Which hook up is hot on a washing machine?

Letter H is stamped out on back of washing machine above or beside correct inlet for hot water.


How can I properly clean the lint filter in the washing machine pan?

To properly clean the lint filter in the washing machine pan, remove the filter from the machine and gently brush or rinse off the lint buildup. Make sure to dry the filter completely before placing it back in the washing machine. Regularly cleaning the lint filter helps maintain the efficiency of the washing machine.


Where is the drain hose located on a washing machine?

The drain hose on a washing machine is typically located at the back of the machine near the bottom. It is usually connected to a drain pipe or standpipe to remove water from the machine during the wash and rinse cycles.


Will the washing machine mess up the leather band in the back of the hat?

It is possible that the washing machine will mess up a leather band on the back of a hat. It is always best to hand wash both hard leather and suede when possible.


How can I fix the breaker for my washing machine?

To fix the breaker for your washing machine, first, turn off the power to the breaker. Then, locate the breaker panel and identify the breaker that controls the washing machine. If the breaker is tripped, reset it by flipping it to the "off" position and then back to the "on" position. If the breaker continues to trip, there may be an electrical issue with the washing machine that requires professional repair.


Where is the drain pump on a Signature washing machine?

On almost all washing machines it is attached immediately below the centre of the tub. It will be easily recognisable by the thick hose going to the back of the machine.


Why would basement washing machine back up from septic?

there is a blockage in your sewer line


Why does the toilet overflow when the washing machine drains?

When the washing machine drains, it can cause the toilet to overflow because both appliances may share the same drain line. If the drain line becomes clogged or blocked, the water from the washing machine can back up into the toilet, leading to an overflow.


Can you transport a new washing machine on its back?

Apparently you can and it shouldn't be a problem - provided it is a front-loading machine, not top-loading ones.....