0
What else can I help you with?
What is the current when 6 coulombs of charge pass through a wire in 2 seconds?
The current is calculated by dividing the charge (6 coulombs) by the time (2 seconds). Therefore, the current is 3 amperes (6 coulombs / 2 seconds = 3 amperes).
How do you calculate charge flow?
Charge flow can be calculated by multiplying the current (in amperes) by the time (in seconds) for which the current flows. The formula is Q = I * t, where Q is the charge flow in coulombs, I is the current in amperes, and t is the time in seconds.
How long it take a current of 10mA of deleiver 30c of charge?
Oh, dude, let's break it down. So, if you have a current of 10mA, which is 0.01A, and you want to deliver 30c of charge, you just divide the charge by the current. So, 30c divided by 0.01A equals 3000 seconds. Easy peasy, right?
If 5.0 Coulombs of electrons flow past the middle of a copper wire in 0.10 seconds then what is the electric current in that wire?
The electric current in the wire is calculated using the formula I = Q/t, where I is the current, Q is the charge, and t is the time. Plugging in the values, we get I = 5.0 Coulombs / 0.10 seconds = 50 Amperes.
How long does it take 9 coulombs to pass a current of 3 amps?
To calculate the time it takes for 9 coulombs to pass a current of 3 amps, you can use the formula: time = charge / current. Plugging in the values, time = 9 coulombs / 3 amps = 3 seconds. So, it would take 3 seconds for 9 coulombs to pass a current of 3 amps.
What is Dielectric test?
The Dielectric Discharge (DD), sometimes called re-absorption current, test is performed during the discharge cycle after the test. There are three components of current (charging, polarization and leakage currents) present during a standard insulation test, which make it difficult to determine the dielectric discharge. Rather than measuring the polarization current during an insulation test, the DD test looks at the de-polarization and capacitive discharge currents at the conclusion of the insulation test. The device under test (DUT) must be charged for an adequate amount of time to be stabilized therefore, the only remaining current component is leakage current. The DUT is then discharged at the completion of the insulation test and the current flow is measured during a standardized time of one minute. This current is dependent on the overall capacitance and the ending test voltage. Dielectric discharge is calculated as: Dielectric Discharge = I (after 60 seconds) / Volts x Capacitance The DD test can identify excess discharge currents that happen when a layer of multi-layer insulation is damaged or contaminated. This condition will be missed by both the spot test and the Polarization Index test. Discharge current will be higher, for a known voltage and capacitance, if an internal layer is damaged. The time constant of this individual layer will differ from the other layers, causing a higher current than for insulation that is good. Homogenous insulation will have a DD value of 0 while good multi-layer insulation could have a value as high as 2. Source: http://www.aemc.com/
What is dielectric discharge test?
The Dielectric Discharge (DD), sometimes called re-absorption current, test is performed during the discharge cycle after the test. There are three components of current (charging, polarization and leakage currents) present during a standard insulation test, which make it difficult to determine the dielectric discharge. Rather than measuring the polarization current during an insulation test, the DD test looks at the de-polarization and capacitive discharge currents at the conclusion of the insulation test. The device under test (DUT) must be charged for an adequate amount of time to be stabilized therefore, the only remaining current component is leakage current. The DUT is then discharged at the completion of the insulation test and the current flow is measured during a standardized time of one minute. This current is dependent on the overall capacitance and the ending test voltage. Dielectric discharge is calculated as: Dielectric Discharge = I (after 60 seconds) / Volts x Capacitance The DD test can identify excess discharge currents that happen when a layer of multi-layer insulation is damaged or contaminated. This condition will be missed by both the spot test and the Polarization Index test. Discharge current will be higher, for a known voltage and capacitance, if an internal layer is damaged. The time constant of this individual layer will differ from the other layers, causing a higher current than for insulation that is good. Homogenous insulation will have a DD value of 0 while good multi-layer insulation could have a value as high as 2. Source: http://www.aemc.com/
What is the duration of Turbo-Charged Prelude?
The duration of Turbo-Charged Prelude is 360.0 seconds.
What is a current electricity?
An electric current is the amount of electrons per unit time or seconds.
What is the duration of Google Current?
The duration of Google Current is 300.0 seconds.
What is the duration of A Current Affair?
The duration of A Current Affair is 1500.0 seconds.
How do I find seconds when a problem gives me mA and C?
Current can be defined as charge / time. Solving for time: time = charge / current. Either convert the current to Ampère, and get a result in seconds, or leave it in mA and the answer will be in kiloseconds (thousands of seconds).
What is the current when 6 coulombs of charge pass through a wire in 2 seconds?
The current is calculated by dividing the charge (6 coulombs) by the time (2 seconds). Therefore, the current is 3 amperes (6 coulombs / 2 seconds = 3 amperes).
What is the duration of Court of Current Issues?
The duration of Court of Current Issues is 1800.0 seconds.
Where to watch history channel shows for free?
so you are charged a minute for every minute you use? or 30 seconds if it is only 30 seconds....
What is the average a person gets charged for possession of cannabis?
Every 45 seconds in America
How do you calculate charge flow?
Charge flow can be calculated by multiplying the current (in amperes) by the time (in seconds) for which the current flows. The formula is Q = I * t, where Q is the charge flow in coulombs, I is the current in amperes, and t is the time in seconds.
