answersLogoWhite

0

No it is not considered a load. A load transforms electrical energy into other types of energy :)

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Physics

Is a light switch a 2nd class lever?

Yes, a light switch can be considered a 2nd class lever. In this case, the fulcrum is located at one end, the effort is applied at the other end, and the load (turning on/off the light) is in the middle. When you push the switch down, you are applying a force, the fulcrum is the pivot point, and the load (activating the light) is in the center.


Is a light switch a first class lever?

Yes, because the fulcrum is in the middle (the part that makes the switch go up and down) the effort is where you push up and down with your fingers the load is your fingers. It is a first class lever.


What is the exact point on which an entire load will balance on a forklift?

The exact point on which an entire load will balance on a forklift is the center of gravity of the load. This point is where all the weight of the load can be considered to act, allowing for optimal balance and stability on the forklift.


Why is the above example a load or an energy source?

The above example is considered a load because it consumes energy from the source it is connected to. It draws power from the source to operate or perform its function. In contrast, an energy source is a provider of energy that can supply power to a load.


Why is the elbow considered a third class lever?

The elbow is considered a third class lever because the effort force is applied between the load (resistance) and the fulcrum. In this case, the biceps muscle (effort force) exerts force between the hand (load) and the joint of the elbow (fulcrum) to produce movement.

Related Questions

Is a switch a load?

No it is not considered a load. A load transforms electrical energy into other types of energy :)


Is a relay considered a load?

The relay's coil(s) would be a load, but the main function of a relay is to act as a switch to control power to a larger load.


What is on load and off load switching?

On load switching is when a switch can be operated whilst current is still passing through the switch (i.e. it is on load) Offload switching is when a switch is operated whilst there is no current through the switch (i.e. it is offload)


What is the least destructive load to switch?

No load is the least destructive load to a switch.


Is a relay defect and open load the same?

A relay is basically a controllable switch that connects a supply voltage to a load. If the relay is switch such that the load is not connected, that could be considered an open load. If it is switched the other way the load will be connected to its supply voltage. A defect in a relay would be something that caused it not to function correctly. It could be in the switch portion of the supply portion of the relay. Hence you are referring to different things and a defect may or may not cause the load to be open.


What happens when you connect the line wire from the switch to the load wire from the wall?

This is what the purpose of a switch is. It connects the "hot" wire to the load. When this is done the load becomes energized.


Where must the function switch be to load radio with comsec?

The switch to load the radio with comsec should be located on the radio itself. It may be a physical switch or button that needs to be activated to enable the comsec loading process.


When a switch is turned off should the load be zero?

The load will be zero after the switch is turned off. if power is still being drawn then the switch is quite likely faulty


What does switch leg mean?

The term switch leg really means switched leg. It is the wire that comes off of the bottom terminal of a switch and when the switch is turned on becomes hot. This is the leg that turns the load off and on.


Is a motor considered to be a load?

Yes. A motor is considered to be a load of the power supply in use.


Why the isolator should not closed with load?

Isolation switches can be closed with loads connected. The isolation switch should not be opened under load unless the switch is load rated. This information can be found on the isolation switch's cover as to the amount of current that can be safely interrupted.


How do you assign a switch to a lamp or load?

yes