0
It may not damage the dryer. But....if the dryer tries to use more than 20 amps, or if anything else is connected to the breaker totaling MORE than 20 amps, the breaker will pop.
The breaker disconnects (throws, pops, etc.) if there is too much current being drawn. Too many light bulbs, heaters, stoves, etc. This is designed as a safety so that wires don't melt, fires start and so on.
Consult the manufacturer to see if is OK. Or at least look at the label on back to see how many amps it uses. If it's even close to 20 amps, it might be good to have an electrician see about upgrading the breaker/ wiring.
What else can I help you with?
How do you know if clothes dryer is hard wired?
Hard wired means that there is no plug and receptacle in the circuit powering the dryer. What you will find is a metal jacketed cable that will come out of the wall or floor and go right into the dryer.
What size breaker do you need for a Whirlpool 4 cycle dryer?
It should take a two pole (220V) 50 amp breaker and matching plug wired with # 8 or # 6 gauge wire. Check your manual.
When you turn on your new tumble dryer what would cause the electricity to trip in all the sockets?
The dryer plug is probably wired wrong, check where the cord is wired to the dryer first. Unplug the dryer befor starting to remove any screws or panels
What is a 30A dryer cord?
A 30 amp dryer cord is the cord that comes attached to new clothes dryer. It is used to transfer the voltage from the wall receptacle to the dryer appliance. Earlier model dryers used to be hard wired directly from the distribution panel to the dryer. Hard wiring is no longer the case as people wanted to take there appliances with them when they moved from one home to another. New homes are now wired with 30 amp receptacles situated in the wall alcove where the dryer is to be situated. This allows the home owner to plug in the dryer without the hiring of an electrician to legally make the connection. Dryers that have been previously been hard wired can be upgraded with a 30 amp cord kit that can be purchased at any hardware store. Following the instructions included with the kits, any home owner can make the conversion and then connect their dryer into the dryer receptacle.
What size breaker should be used for a double oven?
50 amp breaker wired with AWG # 6 wire.
How is a circuit breaker panel wired?
how to connect cables to switches 240 box
What size breaker do you need for two 60W bulbes 110 volts?
It is not the number of bulbs that you worry about. It is the wire size that is your concern. If the circuit is wired with AWG 12/2 wire then use a 20 amp breaker. If it is wired with a AWG 14/2 wire then use a 15 amp breaker. You are protecting the wiring with the correct size breaker.
How big of a circuit breaker needed for two 1500 watt that are 240 volts?
A 30 amp breaker wired with AWG #10 wire.
What amp an outlet is?
Standard recpt. for house hold is 15 AMPS wired usually with 14 awg, but applicance circutis are 20AMPS wired with 12awg. Dryer rect. are 30AMPs wired with 10 awg and Ovens are 50 Amps wired with 6awg.
What is the smallest breaker for a 25 amp circuit?
30 amp wired with AWG # 10 wire.
A parallel circuit breaker should be connected in a parallel to the circuit it's protecting?
For a circuit breaker to protect anything, it must be wired in series with whatever it is protecting.
Can you change a dryer from 120 volts to 240 volts It came wired as 120 volts but we do have an outlet for 240 volts Was hoping to speed up dry times and save some?
If the dryer is a clothes dryer then the short answer no. If it is a hair dryer then there might be a voltage switch on the handle that allows you to change voltages. If the manufacturer of the clothes dryer specified that it can be operated on dual voltages then it is just a matter of changing a few terminal connections. Check the instruction manual to see what it states there. This is very unlikely though. In North America all clothes dryers need 120/240 volts to operate. The 120 volts is used for the timer relays and for the drum motor, the 240 volts for the heating elements in the dryer. By changing to a higher voltage, it will not speed up the speed up the drying time. It is more likely that if you plug the dryer into the 240 volt receptacle it will burn the 120 volt motor out.
