0
Chevrolet
A brand of vehicle, Chevrolet or Chevy was produced by General Motors Company (GM). The car was named after Louis Chevrolet and was set up to sell a variety of mainstream vehicles to compete with Model T by Henry Ford.
6,429 Questions
Where is no 1 cylinder and how are they numbered on a small block chevy?
Number 1 on a small block Chevy is very front cylinder on the drivers side. They are numbered from front to rear on drivers side 1-3-5-7 and on the passenger side front to rear 2-4-6-8. Firing order is 1-8-4-3-6-5-7-2
Where is the horn on a 2006 HHR?
Behind the driver's side headlight. You must remove the plastic fender well to access it. Be careful not to break the plastic plugs holding some of the fender well.
What kind of fuel does a battleship use?
The Russian battleships during the Battle of Tsushima in 1905 burned coal.
The battleships of WWI & WWII burned oil.
Who are Chevy customers and why are the so loyal to that brand?
Because Chevrolet is awesome, and they make/made great cars. ;) For example, the Camaro, or the Astro, the Corvette, and the Chevelle. (Look, I'm even loyal enough to type the whole name)
What is the Minimum rotor thickness for front of a 2005 Chevy Equinox LT?
Minimum thickness is stamped into the rotor. Use a wire brush to remove the rust buildup and you'll see the spec.
Why are you not getting fire to your fuel pump on your 87 Chevy scottsdale?
sounds like you may have a broken wire leading to the pump or maybe its just a blown fuse,check all fuses in panel on side of dash and under hood
When does the Chevy Volt come out?
They Chevy Volt came out in 2010 as a 2011 model, at base price of $32,780
Where is the low speed blower resistor on 1999 Chevrolet siverrado blows only on high speed?
under dash on pasenger side
no
Where is the canister vent solenoid on a 1998 Chevy calivier?
This depends on the actual date manufactured. Most likely under the car next to the fuel tank in the ventialation canister. If you have a code set in the ECM on this solenoid then it was most likely set because when a person pumped gas into the car they tried squeezing that last little bit into the tank and this is a huge NO NO. When this is done it saturates the canister with gas and can cause alot of problems. Basicaly the cheapest way to correct a fuel canister problem is to keep using the car and after all the fuel has evaporated out of the canister the problem will go away. Remember when pumping gas to only pull the triger on the pump half way and take another minute longer to prevent this plus the first time the pump kicks off then it's full. Don't try squeezing that last few since in. Doing this will keep any problems from occurring in the Fuel Ventialation Canister.
What is the required torque for a 1985 Chevy 366 motor for the main and rod bearings?
To what torque should the rod and main bearings of a 1977 366 GMC truck engine be tightened? The rods have 3/8" bolts and it has 4 bolt mains with 1/2" bolts.
Who can id the year or size of the engine serialF0115TGA block casting GM 3994258?
I'm not sure the exact year of the engine, but I just found an engine with the same casting number and due to the offset engine mounts I believe this to be a Chevy 292.
How much did a 1957 fuel injected Chevy cost?
There were 1.5 million Chevys built in 1957 and only 1,530 had the Fuel Injection option. The F.I. was a $484 option. That was allot to pay for an option on a car that cost around $2,500.
Where is the oil filter on a 2009 Chevy HHR?
You access the oil filter from under the hood. On the front right side of the engine, about half way down, locate a 3 1\2 to 4" round black circular cap with (I think it's 30 or 32mm) "nut" on top. Unscrew the cap. The filter will come out with the cap. The filter is a cartridge style filter.
How do you find tire mfg date?
There are a series of numbers printed on the sidewall of the tire, just above the bead area.
They will not be as uniformed or professional looking as the tire size number or printed brand of the tire. One side of the tire will have these additional numbers and the other side won't. The side with the most numbers", will tell you the manufacture date. The last 4 numbers are the date recorded as week and year. For instance if it lists 1608, then the tire was made the 16th week of 2008.
How do you test a ignition coil pack on a 2003 Chevy silverodo?
I found the easiest way to do this is read the codes, if it is reading a misfire on one cylinder, then swap that coil pack with one of the other cylinders coil packs, then you will have to clear the codes and drive it, then see if it throws a new code on a different cylinder.
How do you program key less remote for 06 Chevy Epica?
Check out this website http://www.cheapfobs.com/blog/key-programming/gm-mazda-ford/
worked for me :)
P1174 and p0301 codes on 2007 HHR what is wrong?
Lean Condition caused by bad or restricted injectors
It is a common flaw in the 5.7. Some say put there on purpose to drum up business for the Chevy garages. I never heard anything officially from GM, however, I always thought it odd, that they go out like clockwork, and on everyone of them. At the rear of the motor, the intake manifold buts up to the cylinder head, and water transfers there. The gasket, (a piece of soft material sandwhiched between two pieces of metal to bridge irregularities of the two surfaces) fails in this area, thus leaking water, only under pressure. Not when cold, but hot only. The vehicle is moving, so no puddle. When it is cold, it does not drip, so no signs, in the driveway. Having to add water, on a consistant basis, is a sign. A sweet smell when shutting motor off, and getting out, would be another. The motor running hotter than normal, would be a third. And, it seems to happen every 50,000 miles. At Chevy, I used to charge right around $275, for the process, and the vehicle had to sit overnight. If you choose an outside shop, used one recommended, as this can ba a tricky proceedure.
