0
Dodge
Dodge is a brand of automobiles, sport utility vehicles and minivans in the US, manufactured and marketed by Chrysler Group LLC in over 60 countries and territories around the world.
2,165 Questions
Do dodge trucks have truck beds?
Yes, Dodge trucks have truck beds similar to many other truck designs. These beds vary in size by model. It is also a good idea to consider buying a bedliner, depending on what types of uses you have in mind for your truck.
What is the price range of dodge used cars?
The price range of dodge used cars depends on the type of vehicle. Trucks will range for a little more than a regular car would, also depends on how many miles a person has put on the car, and whether or not there has been work done to the car.
What is causing 93 dodge stealth engine to shut off when car hits bumps then starts back up?
There is a bad electrical connection,
I would start with the Battery and the Engine, Chassis and body grounds, the engine computer grounds.
Pick up the latest edition of "Hemmings Motor News" at your local news stand. You will find someone in that monthly magazine has new ones or rebuilt ones. You could also try going on line for "Hemmings Motor News".
How do you prime a 2008 dodge cummins?
The fuel system on a 2008 Cummins is self priming. Just turn the key on and crank.
The fuel system on a 2008 Cummins is self priming. Just turn the key on and crank.
Why do you get water on floor board of my pickup truck get wet when it rains 1998 dodge sport?
Since it happens only when it rains, it would suggest a few possibilities. Look for these:
- Bad window or door seals.
- Bad windshield seal.
- Holes in the floorboard or firewall, especially near the wheelwells.
Will 17 inch dodge 8 bolt rims fit on 8 bolt 16 inch GMC?
If the Vehicles and Rims are built before 1998, the answer would be Yes, as long as the Offset of the rim is close to the Manufactures Offset Specification.
If the Vehicles and Rims are Newer, Built after 1998, The answer would be No.
In 1998, Ford Manufacture started adopting a metric measurement for their bolt patterns. The other Domestic Car Manufacturers followed their lead there after.
Where is the speedometer hook up locate on a 2000 dodge ram 1500 4x4 with the 46re transmission?
The speedometer signal comes from the abs computer via the rear axle speed sensor.
Depends on what year the truck is and the body configuration (DRW, SRW, etc.)
It is the Chrysler(Dodge) factory scan tool. It stands for Diagnostic Readout Box. The DRB III was is used for vehicles up till the 2006 model year.
How much is a 1985 dodge power wagon pickup worth it is in good condition?
DependS on how many miles it has on it
Is the 1991 Dodge Dakoat fuel injected?
Yes, the 91 Dakota is fuel injected, throttle body fuel injected.
Why won't the scanner read your 2008 dodge cummins?
They weren't designed to be compatible with a simple OBD2 scanner... you'll need someone with the Insite program and appropriate diagnostic connector to read codes.
Can you replace a Dodge 3.9L with a dodge 5.9L?
Probably. The chassis should be wired and bracketed for it, but it would be a lot of work and expense. You would need new transmission and drivetrain, different front springs, maybe rear springs as well, different exhaust system, etc.
What is the most common cause of dodge trouble code p0016?
P0016 - Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)
symptoms
The engine may turn over but not start up
The engine may rattle near the harmonic balancer which means that the tone ring is damaged
The engine may start up and run, but run rough
cause
Timing chain is stretched, or timing belt skipped a tooth because its worn
Timing belt/chain not aligned
Tone ring on the crankshaft slipped or broken
Tone ring on the camshaft slipped or broken
Faulty crank sensor
Faulty cam sensor
Bad wiring to crank or cam sensor
Timing belt or chain tensioner faulty
The fix
Check the cam and crank sensors and their wiring for damage. If you see broken/frayed wires, repair.
If you have a scope, check the cam and crank patterns. If a pattern is missing, suspect a bad sensor or a slipping tone ring.
Remove the cam gear and crankshaft balancer and tone rings for proper alignment, make sure they're not loose or broken and they haven't sheared the alignment key. If they are correctly installed, replace the sensor. If the signal looks normal, then check the timing chain/belt for proper alignment. If it's not aligned, check for a damaged tensioner.
Also check that the belt or chain isn't stretched. replace and recheck.
because they will do anything, go anywhere, pull as much as a semi can, I have a 2004 dodge ram 3500 cummins diesel and we have only had to change one thing that was broken, and it was a water pump, very common to break. I also have a living quarter horse trailer that we have a peterbilt to pull it, we pulled it with the dodge from Oklahoma to Jackson Mississippi and back during the summer, and it came back asking for more. so don't tell me that a dang ford that will break down more than once a day can outpull a dodge.
