Electrical Engineering

chebyshev has less side lobe level compared to binomial arrays

Transients can be currents or voltages. They occur momentarily and fleetingly in response to a stimulus or change in the equilibrium of a circuit.

I think aux relay is part of relay

Explain the difference between the various forms of a.m & f.m and which jutifies the radio station's choice of modulation for each waveband?

it makes a rainbow!!!!!!!!!!!!!!!! :D

Electrical engineering would include such things as transformers and switchgear, conductors, motors and generators; and almost always concerned with the energy component of electrical systems. House and automobile wiring and systems including lighting would also be included.

Electronic engineering is mainly concerned with the information concept of a circuit. Such items such as radios and transmitters, radar and computers, and in general the control of electrical impulses to effect some change. Low energy relays would also be considered part of electronics, for example the suite of relays controlling an elevator system. In general the information component is the focus, rather than the power components.

In short: electrical circuits handle transfer of energy - electronic circuits handle transfer of information

It is a Step-Up Transformer which has 2 times voltage in secondary(HV) than primary(LV)

A transfer switch, in general, switches load between two sources. An automatic transfer switch or ATS is usually installed where a generator is located to allow the generator to give power while electricity is out.

There are only a few parts and components that separate a cordless electric drill from a corded electric drill. Having a battery instead of a cord is the biggest difference.ÊÊ

In the abbreviation scheme that I am familiar with, 1 mv represents 1 millivolt, or 1 X 10 -3 volts. 1 kv represents 1 kilovolt, or 1 X 10 3 volts. So 1 mv would be 1/100,000 of a kv.

It is more reasonable to use square wave rather than sine wave signal to determine slew rate. Both signal sources serve as a functional generator with the sine wave providing high purity waves.Ê

Logical synthesizes maps a register-transfer levelÊdescription to a set of gates. Physical synthesis implements a netlist on a floorplan and improves the quality of the design.

USE INVERTER USE INVERTER USE INVERTER

I FOUND MYSELF WORKING LONG HOURS(OVERTIME WITHOUT PAY) WITHOUT NOTICING IT.

Parasitic resistance is resistance that you encounter in a circuit board or integrated circuit but not included in the original design -- an undesirable, unintended consequence of putting a concept into manufacturing. Since parasitic resistance does exist, you need to estimate its value and make sure the design still functions as intended. An example of parasitic resistance is the resistance of the traces in a circuit board or metal interconnects in an IC, the purpose of which is to connect components electrically according to the circuit diagram, but these connecting structures are not ideal. These connecting structures most likely also add parasitic capacitance and inductance to your design and, if substantial, should be included in your design (back-annotation) accordingly.

317.025280 KILOWATTS = 317,025.28 WATTS

electric fans

LM stands for "Linear Monolithic"

A shunt is an electrical conductor joining points of a circuit, into or out of which current can be diverted. The water-cooled refers to the way it's kept cool, as insulation is not provided.

These! relays operate at a constant time predetermined by adjustment

and are independent of current magnitude as long as it is sufficient

to operate the relay. The time-current characteristic is shown by curve

D in Fig. 2.

These days are generally us&l for radial circuits or for those loop

circuits which have a few sections in series and there is no difference between

the fault current at the end of one s~&on and the beginning of the next

one. This relay is also used for back-up protection to differential and

distaze relays.

If there are several sections in se&s, say more than three or four,

the time of operation increases as the fault location moves closer towards

the source of power and thus the heavier faults get cleared in longer times.

Nom - The resetting current or time or both arc important where hi

is uSed or if the breaker is not supposed to trip. There is a poleibility 8!2zz3

condition may cause the overcurren t relay to operate but a return to normal condition

for a relay wth a low resetting current or a high resetting time is not possible and an

undesired operation may result.

This relay 'may also be advantageously used qn systems where the

Eault current at a particular point varies widely due to the changes in source

impedance, as there is relatively small change in time with the variation of

Gult current.

For earth-fault protection, if the fault current is severely limited

by neutral impedances or by arc or earth resistances, which is often the

case in industrial plant systems, the definite time overcurrent relay may be

used to facilitate co-ordination between two successive sections. In such

cases it is recommended to use relays with similar charact&istics.

It will segregrate the Battery unit and power supply unit,seperate.----Arun

"Nick Holonyak, 75, invented the LED (light emitting diode) in the 1960s."

The amount of light produced and the amount of power consumed. A watt is a unit of power and electrical power is determined using the formula: P = I2*R , Where P is power, I is amps and R is resistance. But using Ohm's law ( V = I * R) the following can be obtained: P = V2/R , Where V is voltage. In US house holds the standard voltage is ~120V, changing the resistance of the filament of the light bulb will change the amount of power consumed and therefore the amount of light produced. The higher the wattage the lower the resistance of the filament. Filaments are used in standard incandescent light bulbs and not in fluorescent tubes or LED fixtures.