answersLogoWhite

0

Frequency Scanners

Scanners can monitor a variety of things: police, fire, EMS, and even air traffic. Although they can't transmit, they are still very useful.

409 Questions

What are the story county Iowa scanner frequencies?

In Story County, Iowa, common scanner frequencies include those used by local law enforcement, fire departments, and emergency medical services. The primary frequencies often fall within the VHF and UHF bands, with some specific channels for agencies like the Ames Police Department and Story County Sheriff's Office. For real-time updates, you can check online resources or scanner apps that aggregate local frequencies. Always ensure you’re compliant with local regulations regarding scanner usage.

How do you program the Radio Shack model 20-308 scanner?

To program the Radio Shack model 20-308 scanner, first, turn on the device and set it to the "Program" mode. Use the keypad to enter the desired frequency or channel number, then press the "Enter" key to store it. Repeat this process for additional frequencies, and remember to save your programming by exiting the "Program" mode. You can also refer to the user manual for specific details on programming features and options.

How do you adjust the speaker volume on Uniden 5.8 Power Max Phone?

To adjust the speaker volume on a Uniden 5.8 Power Max Phone, locate the volume control buttons, typically found on the side of the handset. During a call, you can press the "Volume Up" or "Volume Down" buttons to adjust the speaker volume to your preference. The current volume level is usually indicated on the display. Make sure to test the volume during a call for the best results.

How do you check messages away from home on uniden dect 6.0?

To check messages away from home on a Uniden DECT 6.0 phone, you typically need to access your voicemail remotely. This can usually be done by dialing your home phone number from any phone and, after a few rings, pressing the key to interrupt the greeting. You may then need to enter your voicemail password to listen to your messages. Make sure to consult your specific model's user manual for detailed instructions, as they can vary slightly.

Ten channel scanner reallistic uvhf-hi-lo patrolman scanning receiver but i can't get any frequency out of it what can i do to get frequency out of it?

First, ensure that the scanner is properly powered and that the antenna is connected securely. Check the manual for specific instructions on how to program or scan for frequencies, as different models have varying procedures. Additionally, confirm that you're within range of active frequencies and that the scanner is set to the correct mode (e.g., VHF, UHF). If issues persist, consider resetting the scanner to factory settings or consulting the manufacturer's support for troubleshooting.

How do you set up your Pro-2017 scanner?

To set up your Pro-2017 scanner, first insert the batteries or connect it to a power source. Next, extend the antenna to improve reception. Turn on the scanner and use the keypad to enter the frequency or channel you want to monitor. Finally, adjust the volume and squelch settings to ensure clear audio.

What are bi-naural frequencies?

Binaural frequencies, or binaural beats, occur when two slightly different frequencies are played in each ear, creating the perception of a third frequency in the brain. This auditory illusion is believed to influence brainwave patterns, potentially promoting relaxation, focus, or altered states of consciousness. The difference between the two frequencies typically ranges from 1 to 30 Hz, corresponding to various mental states. Binaural beats are often used in meditation, therapy, and cognitive enhancement practices.

Where can you find scanner frequencies for Washington State?

You can find scanner frequencies for Washington State through websites like RadioReference.com, which offers a comprehensive database of frequencies categorized by region and service type. Additionally, local government or law enforcement websites may provide specific frequencies for public safety communications. Mobile apps like Scanner Radio can also help access live feeds from various agencies in Washington State.

Frequency codes for programming a cobra sr900 police scanner?

To program a Cobra SR900 police scanner, you'll need to input frequency codes for the specific services you want to monitor. Common frequency ranges for police and emergency services typically fall between 150-160 MHz for VHF and 450-470 MHz for UHF. You can find local frequency codes through online databases or scanner forums. Once you have the codes, enter them into the scanner using its keypad or programming software.

Where can you find police frequencies for SchenectadyNY?

You can find police frequencies for Schenectady, NY, through various online resources such as RadioReference.com, which provides a comprehensive database of radio frequencies. Additionally, local government or police department websites may offer information or links to frequencies. Scanner apps and community forums dedicated to emergency services can also be useful for accessing this information.

How do you know or find out what DPi your scanner is?

To determine the DPI (dots per inch) of your scanner, you can check the manufacturer's specifications in the user manual or on their website. Additionally, you can perform a test scan of a known size image and measure the scanned file's dimensions in pixels, then divide the pixel dimensions by the actual size in inches to calculate the DPI. Many scanner software applications also display the DPI settings during the scanning process.

How do I delete a frequency on a Bearcat BC 147xlt?

To delete a frequency on a Bearcat BC 147XLT scanner, first, ensure the scanner is in the correct mode (e.g., frequency or channel mode). Navigate to the frequency you wish to delete using the UP/DOWN buttons. Once on the desired frequency, press and hold the "DELETE" button until you hear a confirmation beep. The frequency will be removed from the memory.

How do you get uniden bearcat bc147xlt off lockout?

To unlock a Uniden Bearcat BC147XLT scanner, press the "L/O" (Lockout) key while the channel you want to unlock is selected. If the channel is locked out, the display will show "L/O." Pressing the "L/O" key again will remove the lockout. Make sure to repeat this process for any other locked channels you wish to unlock.

How do you Lock and Unlock a Regency Z 45 Scanner?

To lock and unlock a Regency Z 45 scanner, press and hold the "Lock" button located on the side of the device until you see the display indicate that the scanner is locked or unlocked. When locked, the scanner will not respond to button presses to prevent accidental changes. To unlock, simply repeat the process. Always refer to the user manual for specific instructions and troubleshooting.

How do you reset a Uniden bearcat scanner?

To reset a Uniden Bearcat scanner, first turn off the device. Then, while holding down the 'Hold' and 'Function' buttons, turn the scanner back on. Continue to hold the buttons until the display shows "Initializing" or "Resetting." This process will restore the scanner to its factory settings, erasing any stored frequencies and settings.

How do you program a uniden dc355n to hear police activies?

To program a Uniden DC355N scanner to hear police activities, first, ensure the scanner is set to the correct frequency range for your local police departments. Use the manual to find the specific frequencies or codes used by your local law enforcement. Enter these frequencies into the scanner by switching to the programming mode, and then input the desired channels. Finally, save your settings and switch to the scanning mode to listen for police communications.

Where can you find a free list of local scanner channels?

You can find a free list of local scanner channels on websites like RadioReference.com, which offers an extensive database of scanner frequencies by location. Additionally, apps like Scanner Radio and Broadcastify provide access to live feeds and lists of local channels. Local amateur radio clubs or community forums may also share frequency information.

How do you program your bc60xlt-1 Uniden Bearcat scanner in Washington state?

To program your BC60XLT-1 Uniden Bearcat scanner in Washington State, first, locate the frequencies for local police, fire, and emergency services, which can often be found on websites like RadioReference. Turn on the scanner and press the "MAN" button to enter manual mode, then use the keypad to enter the desired frequency. You can also program channels by accessing the "PRG" mode, selecting an empty channel, and entering the frequency. Finally, ensure that you save your settings and scan for the programmed channels.

Can you purchase longer antennas for a Uniden BC72XLT scanner?

Your scanner uses a standard BNC antenna connector. Check eBay and ScannerMaster.com for available antennas.

How do you program a uniden bearcat handheld scanner model bc245xlt?

To program a Uniden Bearcat BC245XLT handheld scanner, first power on the device and press the "MANUAL" button to select a channel. Use the keypad to enter the desired frequency, then press "E" to save it. For trunked systems, press the "TRUNK" button, select the trunk type, and enter the control channel frequency. Finally, use the "SCANNER" button to start scanning the programmed frequencies.

How do you program a uniden bearcat bc60xlt?

To program a Uniden Bearcat BC60XLT scanner, first, turn on the device and select the frequency band you want to program. Use the "Manual" button to enter the desired frequency, then press "Enter" to save it to the selected memory channel. You can also use the "Search" feature to find active frequencies within a range. For more advanced programming, consult the user manual for details on using the memory banks and scanning modes.

Which is a scanner lpo or hpo?

An LPO (Low Power Optical) scanner is typically used for scanning documents at lower resolutions and is often more cost-effective for everyday use, while an HPO (High Power Optical) scanner provides higher resolution and faster scanning capabilities for professional or high-volume environments. The choice between LPO and HPO scanners depends on the specific needs of the user, such as the required image quality and scanning speed. Generally, LPO scanners are suitable for basic tasks, while HPO scanners are better for detailed or specialized scanning applications.

How do you program the bearcat bc60xlt in Tennessee?

To program the Bearcat BC60XLT scanner in Tennessee, start by identifying the frequencies used by local agencies, which can typically be found online through databases like RadioReference. Turn on the scanner and use the manual to enter the frequencies into the appropriate memory channels. You can also use the frequency search function to scan for active channels. Lastly, save your programmed frequencies and ensure the scanner is set to the right mode to listen to those channels.

What is mhl on police scanner?

MHL on a police scanner typically stands for "Mental Health Law." It refers to incidents involving individuals experiencing mental health crises, where law enforcement may be called to intervene. These calls often involve the assessment of the individual's mental state and may lead to the involvement of mental health professionals for support and care.

How do you program a Uden Bearcat 30channel10 Band Radio scanner?

To program a Uden Bearcat 30 Channel 10 Band Radio scanner, first turn on the scanner and select the channel you want to program. Press the "Manual" button to access the channel, then press the "Program" button. Enter the desired frequency using the number keys, and confirm by pressing "Enter." Repeat this process for additional channels, and be sure to save your settings before exiting programming mode.