answersLogoWhite

0

Honda Fit

The Honda Fit, also called the Jazz in other parts of the world, is a subcompact car produced from 2001 to present by the Japanese automaker Honda. It runs in both gasoline, hybrid (gasoline-electric), and all-electric variants.

357 Questions

How long is the 2010 Honda Fit?

The 2010 Honda Fit is 13 ft. 5.6 in. (161.6 in.) long.

How do you reset the oil life on a Honda Fit?

Turn the ignition switch to the ON (II) position

Press the Select/Reset knob repeatedly until the engine oil life is displayed.

Press the Select/Reset knob for about 10 seconds, The engine oil life and the maintenance item code(s) will blink.

Press the Select/Reset knob for another 5 seconds. The maintenance item code(s) will disappear, and the engine oil life will reset to "100".

Fuel filter located on a 2006 Honda Jazz?

fuel filter location on honda jazz 2006 is under the centre console

I plan on financing a new Honda Fit Sport. I don't have experience with this as this will be my first car. Whats the best way to get a Low rate and what are the procedures for this?

A key angle will be to scout for car loan companies offering the least expensive auto finance. One must understand that the auto finance may must be reimbursed over a long term. While the going may be fine at present, yet the future may have a couple stresses in store. Subsequently, that makes it fundamental to find car finance companies offering low rate car finance. The center ought to be in a near investigation of what definitely auto finance companies in Australia may be putting forth. One can surely assess every one of the alternatives close by and recognize organizations offering the advance at a cheap rate of interest.

What is the base engine size of the 2007 Honda Fit?

The 2007 Honda Fit has a 1.5 L base engine size.

What does VSA stand for on the Honda jazz?

VehicleStability Assist (VSA) System

http://techinfo.honda.com/rjanisis/pubs/om/md0404/MD0404O00183B.pdf

What is the front leg room in the 2008 Honda Fit?

The 2008 Honda Fit has 41.9 in. of front leg room.

Will a stereo from a 1999 Honda Fit in to a 1995 Honda?

The wiring harness from the 1999 stereo has a 21 prong plug and the 1995 has a 14 prong plug you can purshase a harness from Honda but it has to be hadrwired to the exsisting wiring but don't screw it up, go to Honda and get a wiring diagram for the both of them to match up the wiring you need to make it work.

How do you reset the Maintenance Required light on a 2007 Honda Fit?

Tombasay Turn the ignition switch to the ON (II) position.

Press the Select/Reset knob repeatedly until the engine oil life is displayed.

Press the Select/Reset knob for about 10 seconds or until the engine oil life and the maintenance item code(s) will blink. Stop pressing.

Press the Select/Reset knob again, for another 5 seconds or until the engine oil life resets o "100".

How many O2 sensors does a 2008 Honda Fit have?

The 2008 Honda Fit is equipped with two oxygen (O2) sensors: one upstream (pre-catalytic converter) and one downstream (post-catalytic converter). The upstream sensor helps monitor the air-fuel mixture, while the downstream sensor checks the efficiency of the catalytic converter. If either sensor fails, it can trigger a check engine light and affect vehicle performance.

How do you reset the maintenance minder light in a Honda Fit?

To reset the maintenance minder light in a Honda Fit, start by turning the ignition to the "ON" position without starting the engine. Press the "Trip" button until the display shows the maintenance menu. Then, with the maintenance minder displayed, press and hold the "Trip" button for about 10 seconds until the light goes off. Finally, turn off the ignition, and the reset should be complete.

How do you fit a new bumper to a Honda jazz?

To fit a new bumper to a Honda Jazz, first, ensure the vehicle is securely parked and turned off. Remove any screws, clips, or fasteners securing the old bumper, typically located in the wheel wells, undercarriage, and at the top of the bumper. Carefully detach the old bumper from the vehicle, then align the new bumper with the mounting points, securing it with the appropriate fasteners. Finally, check that all clips and screws are tightened and ensure proper fit and alignment before closing the hood and testing the installation.