0
Massey Ferguson
Massey Ferguson is a major producer of tractors and other farm equipment. They manufacture combines, balers, planters, loaders, and several other machines that help keep a farm going.
793 Questions
How does the hydraulic oil get into the engine on a Massey Ferguson 1155?
When you pour it in the crankcase fill spout.
How do you time a Massey Ferguson 126 wire tie baler?
To time a Massey Ferguson 126 wire tie baler, first ensure the baler is properly set up and connected to the tractor. Then, disengage the tractor's PTO and manually rotate the baler’s flywheel to access the timing marks on the crankshaft and connecting rod. Align these timing marks according to the manufacturer’s specifications, typically found in the operator’s manual. Finally, reassemble any removed components and test the baler to ensure it operates smoothly and efficiently.
How does diesel get in oil pan on 231 Massey Ferguson tractor?
the diaphram in the fuel lift pump goes bad and leaks fuel into the engine
Where do you put hydraulic oil in Massey Ferguson tractor?
Hydraulic fill is on top of the transmission but be sure to remove both drain plugs at the trans and back end as they are connected before refilling.
How do you stop a Massey Ferguson tea 20 1946 carburetor from leaking out petrol?
take the carb off and apart to clean it. it probably has some dirt/rust in it causing the needle not to seat. also check the float for buoyancy.
How do you stop a Massey Ferguson tea 20 1946 fuel tap from leaking out petrol?
Reseal or replace the valve.
What type oil for Massey 1528?
For the Massey Ferguson 1528, it is recommended to use SAE 15W-40 engine oil that meets the API service classification of CJ-4 or higher. This oil provides proper lubrication and protection for the engine under various operating conditions. Additionally, for the hydraulic system, you can use hydraulic oil that meets the specifications set forth in the owner's manual. Always consult the owner's manual for specific recommendations and guidelines.
What year is serial number A 0150 Massey Ferguson 20F tractor?
The serial number A 0150 on a Massey Ferguson 20F tractor indicates that it was likely manufactured in the early 1960s. Specifically, the Massey Ferguson 20F was produced between 1958 and 1961, so the tractor associated with this serial number may fall within that timeframe. For an exact year, further details or a more specific serial number reference would be required.
What size oem tires are on a Massey Ferguson model 12 baler?
6.50 X 15 RIBBED on the heavy side (left)
6.00 x 15 Ribbed on the light side (right)
Did Massey Ferguson make a model 32 tractor?
No, Massey Ferguson did not produce a model specifically called the "32" tractor. However, the company has manufactured various models with similar numbers, such as the MF 30 and MF 35 series. If you're looking for details on a specific model, please provide more context or check the exact model number.
Where do you put hydraluic oil in a Massey Ferguson 231?
A MF 231 holds about 9 gallons of hydraulic oil and is added via a plug in top of the transmission housing.
How do you check the hydraulic fluid in a 492 Massey Ferguson?
The dipstick for the hydraulic fluid is hard to see straight on. If you stand behind the tractor and look behind the right arm of the three point hitch you will see a yellow dipstick. The dipstick is scored on either side to indicate min and max levels,
How do you change the hydraulic fluid filter on a Massey Ferguson 275?
where do u put hydraulic fluid in a Massey Ferguson 275
How do you bleed the injectors on a Massey Ferguson 230 diesel?
Loosen the bolt on the top of the injector for cylinder #1, located on the left side front of the engine, under the fuel tank. Prime the system with the manual pump located on the right side of the tractor to the rear of the fuel filter and above the starter. Prime until clear fuel without air spills from the injector. Repeat for injectors 2 and 3. If you have someone to crank the engine, you can close and open each injector repeatedly. Close the injector, build pressure, then release. It takes a while, stay with it.
What type oil is used in massey ferguson 1428 rear end?
Use Massey Ferguson hydraulic oil or an equivalent due to the unit having a wet brakes and clutch, regular hydraulic oil will give you problems down the road.
