0
MINI Cooper
The Cooper is an economical, inexpensive and nimble car manufactured by the British Motor Corporation with the help of John Cooper, a builder and designer of rally and Formula One cars.
1,392 Questions
What size engine does the 2008 Mini Cooper-Clubman have?
The 2008 Mini Cooper-Clubman has an inline 4 engine.
What is the curb weight of the 2010 Mini Cooper-Clubman?
The curb weight of the 2010 Mini Cooper-Clubman is 2723 lbs..
What was mini father occupation in the cabuliwallah?
In Rabindranath Tagore's story "Kabuliwala," Mini's father is a writer. He is depicted as a thoughtful and observant character who reflects on the relationship between his daughter and the Kabuliwala, a fruit seller from Afghanistan. Through his profession, he provides a narrative lens that explores themes of childhood innocence and the bonds formed between different cultures.
Where is the pollen filter on a BMW mini?
The A/C filter aka cabin filter (which filters out dirt, dust, pollen etc.) is located underneath the glove compartment. You need to remove the plastic cover either by releasing the clips, or by removing screws (depending on your model). There are two types of filters, one with carbon and one without. The addition of active carbon helps filter out odors and pollutants too.
A cheaper alternative to the Mini OEM Filter is made by MicronAir.
Installation instructions: http://www.micronair.com/files/products/MP130_MC630.pdf
Picture of filter without carbon: http://www.micronair.com/files/products/images/MP_130.jpg
Picture of filter with carbon: http://www.micronair.com/files/products/images/MC_630.jpg
Where can one purchase a mini fan?
Mini fans can be purchased online at popular websites such as Amazon and eBay. Alternatively, one could try Paramount Zone, Mini Sport, TLC Direct and Maplin.
How do you remove the power steering pump on a mini?
Tools and supplies needed:
10, 13mm sockets with ratchet and extension(s)
Medium side-cutters (6" or so) to remove the crimped hose clamp.
Floor jack and pair of jack stands
New hose clamp
Small screwdriver to release the tabs on the power connector
Medium screwdriver to install the new hose clamp
Drain Pan to catch the mineral oil
1L can of Pentosin CHF 11S
Optional: new O-ring for the high pressure line
De-greaser to remove spilled oil
Procedure:
1. Remove the two 13mm nuts that attach the fan bracket to the PS pump bracket
2. Disconnect the fan electrical connector and set the fan assembly aside.
** This would be a good time to check the fan to make sure it spins smoothly and easily.**
3. Remove the two connectors from the PS pump. - The small connector has one retainer that can be released by squeezing the tab toward the connector body. - The large connector has two tabs that need to be released by gently prying them away from the connector body. It is easy to break these tabs.
4. Remove the hose clamp from the hose that goes to the reservoir. Since it is crimped on it can be a PITA to remove. I have successfully at removed these by putting a screwdriver in the crimped area and prying the crimped area apart. YMMV
5. Remove the 13mm bolt that holds the high pressure line to the pump.
6. Position the catch pan to catch the oil that will spill when the hose is removed from the pump. - You may want to have some rags handy to keep the oil off the sub-frame. Clean up will be easier this way.
7. Remove the two hoses.
8. Remove the 13mm nut and the two 13mm bolts that attach the PS pump bracket to the sub-frame - The two bolts are visible (barely) at the rear of the sub-frame in the area of the down-pipe.
9. Drop the pump far enough to remove the wire retainer clip.
10. Remove the pump.
11. Remove the four 10mm nuts that hold the pump to the mounting bracket.
12. Installation is the reverse of removal.
The thing that was the most frustrating was the removal of the low pressure hose. Everything else was pretty straightforward. If you have everything ready to go, it should only take about 1/2 hour or so. Partly depends on how difficult it is to remove the hose clamp.
if you are looking for an ordinary 1.0l mini 2,3000 pound if you are looking for a cooper ive seen prices over 20,000 pound so whatever you want its your choice but remember to check for rust and also mantain the engine well as ive heard they can be quiet unreliable
What kind of fuel does the 2013 MINI Cooper use?
The 2013 MINI Cooper runs on premium unleaded (required).
What kind of fuel does the 2014 MINI Cooper use?
The 2014 MINI Cooper runs on premium unleaded (required).
What is paring sekular is a mini area of republko?
It seems there might be a typo in your question, as "paring sekular" and "republko" are not recognized terms. If you're referring to a specific concept or region, please clarify or correct the terms, and I would be happy to help you with more accurate information!
What is the drag coefficient of the 2011 Mini Cooper-Clubman?
The 2011 Mini Cooper-Clubman has a drag coefficient of 0.32 Cd.
What ground clearance does the 2014 Mini Cooper-Paceman have?
The ground clearance of the 2014 Mini Cooper-Paceman is 0 ft. 5.3 in. (5.3 in.).
How many valves does the 2011 Mini Cooper-Countryman have?
The 2011 Mini Cooper-Countryman has 16 valves.
How long is the 2008 Mini Cooper-Clubman?
The 2008 Mini Cooper-Clubman is 12 ft. 11 in. (155 in.) long.
What are the dimension of a mini?
Each year and style of mini has slightly different dimensions. To answer this properly you would need to know the year/make of the mini.
what are the dimensions of a 2010 mini cooper
What year did the original mini some out?
The Classic Mini was first introduced in 1959 with an 850cc engine
www.HeritageGarage.com
DSC = Dynamic Stability Control There is a very good explanation of what it is and how it works at this URL: http://www.bmwworld.com/technology/dsc.htm Hope this is helpful.
