answersLogoWhite

0

A Wall/Back Plate Elbow is used to secure a bib tap (tap installed above a cleaners sink) over Belfast sinks or other outdoor/cleaning type sinks.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

What type of mail box is secure for outside usage?

What you are looking for is called a surface mounted letterbox, they can be fitted on any wall or partition and give a stylish and functional look. You also have the option of fitting them horizontal or vertically.


What is the best method for applying flare fitting sealant to ensure a secure and leak-free connection?

The best method for applying flare fitting sealant to ensure a secure and leak-free connection is to clean the fitting thoroughly, apply a thin and even layer of sealant to the flare surface, and then carefully tighten the fitting to the recommended torque specifications. This will help create a tight seal and prevent leaks.


How can I connect PEX tubing to a water heater?

To connect PEX tubing to a water heater, you can use a fitting called a PEX fitting. This fitting is designed to connect the PEX tubing to the water heater securely. Simply insert the PEX tubing into the fitting and use a crimping tool to secure it in place. Make sure to follow the manufacturer's instructions for the specific type of PEX fitting you are using.


What is an anchor line hole called?

An anchor line hole is typically called a fairlead or a chock. It is a fitting on a boat or ship that guides the anchor line to ensure proper handling and secure anchoring.


How do you properly use a compression fitting?

To properly use a compression fitting, first ensure the pipe end is cut cleanly and squarely. Slide the compression nut and ferrule onto the pipe, then insert the pipe into the fitting. Tighten the nut onto the fitting by hand, then use a wrench to secure it further. Check for leaks once the fitting is tightened.


How can I connect a galvanized pipe to a sharkbite fitting?

To connect a galvanized pipe to a SharkBite fitting, you can use a SharkBite transition fitting specifically designed for this purpose. Simply push the fitting onto the galvanized pipe until it clicks into place, ensuring a secure connection without the need for soldering or special tools.


How can I properly push on copper fittings to ensure a secure and leak-free connection?

To properly push on copper fittings for a secure and leak-free connection, make sure the pipe is clean and deburred, apply flux to the fitting and pipe, insert the pipe fully into the fitting, and use a proper tool to press the fitting onto the pipe. Heat the joint evenly and allow it to cool for a strong seal.


How can I properly install an MFL fitting for my gas line?

To properly install an MFL fitting for your gas line, follow these steps: Turn off the gas supply. Clean the pipe ends and the fitting. Apply pipe thread sealant to the male threads of the fitting. Connect the fitting to the pipe, ensuring it is tight. Use a wrench to secure the fitting in place. Turn on the gas supply and check for leaks using a soapy water solution. If there are no leaks, your MFL fitting is properly installed.


How to install a SharkBite fitting properly?

To install a SharkBite fitting properly, first cut the pipe cleanly and squarely. Then, push the fitting onto the pipe until it reaches the depth mark. Make sure the pipe is fully inserted and secure. No soldering or glue is needed for SharkBite fittings.


What is the Hindi word for secure?

secure is often called 'surakshit' in hindi.


How do you make a bracelet using pipe cleaners an plastic beads?

You find 2 pipe cleaners and beads that have holes that will fit through pipe cleaners. Next you put the beads on the pipe cleaners and tie the 2 pipe cleaners together. Now you have your bracelet. I knew this because i did it myself thanks for reading this


Why are flat washers used with nuts and bolts called washers?

Flat washers are called washers because they are used to distribute the load of a nut or bolt over a wider area to prevent damage to the surface being fastened. They "wash" out any imperfections on the surface and create a more secure connection.