answersLogoWhite

0

The pilot setting will heat the water a few degrees. A gas water heater will have a thermal rating in BTU of 30,000 to 80,000. The pilot light by itself will have about 1,000 BTU. Operating overnight with no water movement and a well-insulated tank, you will observe a temperature rise but certainly not enough for clothes washing, dishwashers, or showers.

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

Hot water heater pilot light works heater wont light?

Have you turned the control from Pilot to On? Have you increased the temperature setting?


How do I turn on the water heater pilot?

To turn on the water heater pilot, locate the pilot light button or knob on the water heater. Turn the knob to the "pilot" setting and hold it down. While holding the knob down, use a long lighter to ignite the pilot light. Once the pilot light is lit, continue holding the knob down for about a minute before releasing it. This should successfully turn on the water heater pilot.


Does the water heater still fill with water when the pilot light is off?

Yes


How can I relight the water heater pilot?

To relight the water heater pilot, locate the pilot light button or knob on the water heater. Turn it to the "pilot" setting and hold it down. While holding the button down, use a long lighter to ignite the pilot light. Keep holding the button for about a minute after the pilot light is lit to ensure it stays on. If the pilot light continues to go out, there may be an issue with the thermocouple that needs to be addressed by a professional.


When the pilot light is off does the water heater still fill up?

The water continues to run into and out of the water heater. There is just no flame to heat it up.


How do I start a gas water heater?

To start a gas water heater, first make sure the gas supply is turned on. Then, locate the pilot light and follow the manufacturer's instructions to relight it. Once the pilot light is lit, adjust the temperature setting on the water heater to your desired level. Allow the water heater to heat up the water before using it.


How do I turn on the pilot light for my water heater?

To turn on the pilot light for your water heater, locate the pilot light assembly near the bottom of the water heater. Turn the gas control knob to the "pilot" setting and hold it down. While holding the knob down, use a long lighter to ignite the pilot light. Once the pilot light is lit, continue holding the knob down for about 30 seconds before releasing it. If the pilot light stays lit, turn the gas control knob to the "on" position to start the water heater.


How to light a water heater with an electronic pilot by Honeywell?

To light a water heater with an electronic pilot by Honeywell, follow these steps: Locate the control panel on the water heater. Turn the control knob to the "Pilot" position. Press and hold the pilot button while pressing the ignition button. Continue holding the pilot button for about 30 seconds to allow the pilot flame to ignite. Release the pilot button and turn the control knob to the desired temperature setting. Always refer to the manufacturer's instructions for specific details on lighting your water heater.


Should your hot water heater be on pilot or on?

"Pilot" is only when initially igniting your water heater. Some manufacturers state to leave it on "Pilot" for so many minutes before turning to on but this is only temporary. It should be then turned to "On" and then if you have a low, medium or high setting or degrees adjustment, adjust the temperature setting. Remember that most local plumbing codes and water heater manufacturers recommend a temperature of no more than 120 degrees F.


How do I turn on a gas water heater?

To turn on a gas water heater, locate the pilot light and turn the knob to the "pilot" setting. Press and hold the knob down while using a long lighter to ignite the pilot light. Once lit, continue holding the knob down for about 30 seconds before releasing it. Then, turn the knob to the "on" position to start the water heater.


How do you light a pilot light on a water heater?

To light a pilot light on a water heater, locate the pilot light button or knob on the control panel. Turn the knob to the "pilot" setting and hold it down. While holding the knob down, use a long lighter to ignite the pilot light. Keep holding the knob down for about 30 seconds to allow the pilot light to stay lit. Release the knob and switch the control panel back to the desired temperature setting.


Why does the water heater pilot go out?

The water heater pilot can go out due to issues such as a faulty thermocouple, a dirty pilot light, or a lack of gas supply.