0
If you can get to the 6 inch cast iron, you could use a rubber coupler between the cast and the flange. If it is in the concrete, put a piece of 4 inch PVC inside the 6 inch and lead it in like you would a regular cast joint. Leave the 4 inch above the floor and slide the flange over it, screw it down and cut the 4 inch flush with the flange. They make just the flange that will slide over the pipe.
What else can I help you with?
What is a compression flange?
A compression flange is used to connect a toilet to the sewer line.
What is the purpose of a toilet floor flange and how does it contribute to the installation and stability of a toilet?
A toilet floor flange is a piece of plumbing that connects the toilet to the floor and the sewer pipe. It provides a secure base for the toilet to be bolted onto, ensuring stability and preventing leaks. The flange also helps to create a proper seal between the toilet and the sewer pipe, preventing odors and wastewater from escaping. Overall, the floor flange is essential for the proper installation and stability of a toilet.
What does the wax ring on the toilet do?
It seals the gap between the base of the toilet and the toilet mounting flange so that sewage and sewer gases don't escape into the building.
Is sewer gas escaping if the toilet is not installed yet?
Yes. There is no pressure involved, so most anything set over it will be enough or a wad of paper in the flange.
Toilet Flange Repair?
When a toilet rocks like a rocking chair, leaks water around the floor connection or displays other signs of insecure foundation, the toilet flange needs replaced or reset. A toilet flange is the metal plate located below the toilet which connects the toilet with the sewer outlet pipe while securing the toilet with the floor. When a toilet is initially constructed it is secured to the floor with screws and the junction is sealed with a liberal application of beeswax. When a toilet is securely fastened and maintained properly, proper function including no water leakage or odor present is the norm and not the exception. An indication of possible need of attention is the presence of black mold on the floor near the base of the toilet. Also evidence of water leakage or an unpleasant odor originating from the toilet base is a reliable indicator of the need for a toilet flange repair. Regardless of who does the repair of a toilet flange, the following criterion is paramount for a job well done. It is also important to follow certain procedures, from diagnosis to completion of the job. Tools and materials: screws, screw driver, flange bolts, wax rings, caulk and a flange repair kit. Remove the Toilet: After shutting the water supply to the toilet, flush the toilet water from the tank and bowl before releasing the toilet from its floor connection. Unscrew the bolts and nuts on the sides of the toilet base. Secure the bowl and tank and lift the toilet from the floor connection. Repair the Toilet Flange: Old wax must be cleaned off from the old flange. Flange bolts may need replaced due to corrosion from water leakage. Position the flange bolts in the holes of the repair kit and place it on the floor as the previous flange setup. This step ensures proper placement of the flange and prevent leakage. Fix the Flange and Toilet: Follow manual instructions of the original toilet manufacturer when screwing the flange to the floor. Place wax rings and remount the toilet with bolts and nuts.
How do you replace a PVC flange over sewer drain?
flange off tool.....Locke Supply carries them
How did the fish get in the sewer?
some people flush their fish down the toilet when it dies, and the toilet is connected to the sewer.
What do you do when the sewer is above the plumbing line and you need to install a toilet?
Your home improvement warehouse store or bathroom contractor should have "flush-up" toilet kits (sewage ejector pump, Qwik Jon is one I have installed. These are very handy where no sewer is available for standard toilet installation. The kit consists mainly of a tank and pump that will carry waste to the existing sewer lines and misc. parts and installation instructions. You provide the toilet and PVC from tank to sewer. They run about $800-$1000 depending on your needs (toilet only, or toilet, lav, & shower configuration). These require a GFCI outlet nearby so you may need an electrician, the rest is very easy. Good luck. In addition to the installation instructions I would recommend installing a "clean-out" in your PVC, especially if you are pumping a considerable distance, in case a clog develops.
Do toilets overflow?
the toilet overflows if either the building sewer, branch line in your sewer system or trap in your toilet gets clogged.
How can I install a toilet in the basement?
To install a toilet in the basement, you will need to first determine the location for the toilet and ensure there is proper plumbing access. Next, you will need to install a sewage ejector pump if the basement is below the level of the main sewer line. Then, connect the toilet to the sewage ejector pump and the main plumbing system. Finally, secure the toilet in place and test for proper functionality. It is recommended to consult a professional plumber for assistance with this installation.
Services?
Emergency Plumbing Cheap Plumber Tankless Heater Installation Water Heater Repair Fix Clogged Toilet Toilet Installation Bathroom Sink Drain Repair Sewer Drain Cleaning Install Garbage Disposal
Can you remove a toilet and floor over drain?
The toilet flange is usually above the floor level. You would have to cut it off the drain pipe and cap it. How you do this depends on what type of pipe the drain is made of. Even if the drain should be below the floor level, you have to seal the drain or sewer gas will come up from the drain.
