0
The distance for running an ejector pump sewage line typically depends on the specific pump's capacity and the pipe diameter. Generally, you can run a sewage line up to 100 feet horizontally; however, this can vary based on factors like the elevation change and the type of piping used. It's essential to consult the manufacturer's specifications and local Plumbing codes to ensure proper installation. Additionally, using appropriate fittings and maintaining proper slope can help optimize the system's efficiency.
What else can I help you with?
How long of a hose can be used on a sump pump?
A sump pump discharge line should run as far from the foundation walls as possible.
1998 Monte Carlo fuel relay switch My fuel pump is not getting any fuel to the fuel pump. So far I have found 2 vacuum leaks. When I remove the cap at the end of the fuel line there is no hissing?
on a 1998 chevy monte carlio i have a problem the engine start but cut off and i chech the fuel line coming from the pump and the pump pumping fuel but low pressure is this mean the pump is bad?
Where is the vacuum pump on 03 5.9 cummins?
Drivers side of engine. Locate your power steering pump by following line from reservoir. vac pump is located directly behind ps pump. By directly behind, I mean the ps pump actually piggybacks the vac pump. The previous answer is for 2002 and prior. On the 2003 the vac pump is an electric pump on the far passenger side, up near the firewall.
When was Far North Line created?
Far North Line was created in 1874.
Why lake receives more water from sewage than natural water?
One reason a lake may receive more water from sewage than from natural falling rainwater may be that there are far more sewage outlets due to an urban setting. Another may be that the lake is near a water treatment plant and a large metropolitan area.
How do you replace a fuel pump for a 1996 GMC Sonoma The pump is held in place by a 4inch snapring and the problem is the new fuel pump does not seem to go down far enough for me to replace the ring?
the pump you have may be the rong one or you must use the greese that comes with the new pump and put it on the new O-ring then you must line up the tab facing the front and push down hard the pump is spring loaded so it will go down and the O- ring is a tight fit.
Can you replace a cast iron sewage pipe with PVC pipe in New york City?
As far as I know PVC is illegal in New York and Chicago.
Where are the fuel pump fuse relay on a 1990 Chevy caprice with a 350 motor?
Under the bonnet , along the fire wall on the rigth side not far from the wind screen cleaning system. Either it is a 20 amp on line or a separate fuse in a connector located near the thefuel pump relay.
Why is fuel gauge stuck on full after changing fuel pump on a 2000 Ford Excursion?
That usually happens when the pump is turned too far in the tank and the float is hitting the side of the tank.That usually happens when the pump is turned too far in the tank and the float is hitting the side of the tank.
What is the first line in the script for the Star Wars movies?
The first line is, "A long time ago, in a galaxy far, far away...".
How many types of hydraulic pump?
As far as I know, according to the volume of oil absorption and realize the function of oil to points， the hydraulic pumps can be can be divided into gear pump, vane pump, plunger pump and viscosity pump.
How do you tell if it's the pump or the hose leaking power steering in a Chevy Monte Carlo?
Turn your vehicle off and then wipe the excess fluid from the power steering pump and line. Survey the power steering pump to see if their are any holes or dings. It may be hard to see so try using your hand to feel around. You may have to wait for engine to cool. If you did not find any leeks then top off the power steering fluid. Watch the power steering line while having a partner or friend turn the engine on and turn the steering wheel fully in one direction and the same in the opposite direction. Watch the power steering line to see how far up it is leaking. If you can not see where it is leaking because of too much fluid leaking, then re-wipe and try again. If you still can't tell then take the line off and make sure the hole on the pump where the bolt goes in is not damaged. Then make sure the bolt itself is not damaged.If the hole or pump is damaged then you need a new pump and if the line or bolt is damaged you need a new line.
