answersLogoWhite

0

A: TTL gates operates on the premise of having +5 dc on the rail therefore the output will be in the range +5 volts. A cmos gate while similar to a TTL function is not really compatible since the output volts can be 12 volts or more. Besides that TTL gates require some input current for it to operate

User Avatar

Donato White

Lvl 10
3y ago

What else can I help you with?

Related Questions

What is a TTL-compatible output?

Compatibility in TTL means that the output of one TTL device can be used to drive the Input of the other TTL device , This because the low and high output window fit inside the low and high input window/profile TTL stand for Transistor Transistor Logic, so any voltage between 0 and 5 volt is compatible where any voltage between 3V and 5V is logic 1 and zero volt is logic 0


Ttl logic family has an output state known as?

true and false


Which logic family has the least propagation delay?

Here are the propagation delays for these gatesa) ECL = 2nsb) TTL = 1.5-33ns depending on the type of TTL. Conventional TTL is 9ns, Advanced Schottky TTL is 1.5nsc) RTL = 25nsd) CMOS = 5-20ns depending on if it is conventional CMOS, TTL pin compatible CMOS, high speed TPC CMOS or TTL compatible CMOSSo the fastest would be the Advanced Schottky TTL (74ASxx) at 1.5ns but the choice simply said TTL which I would interpret as Conventional TTL (74xx/54xx) which would have a propagation delay at 9ns.So the winner is ... (a) ECL which has a propagation delay at 2ns.


Is the 8086 and 8088 TTL compatible?

Yes, the 8086 and 8088 microprocessors are TTL (Transistor-Transistor Logic) compatible. Both processors were designed to work with standard TTL logic levels, allowing them to interface with other TTL-compatible components in a system. However, the main difference between the two lies in their data bus width; the 8086 has a 16-bit data bus, while the 8088 has an 8-bit data bus, which affects their performance and system design.


Can DTL logic work with TTL logic?

Yes, standard 5V powered DTL and TTL devices are fully input/output logic level and fanout compatible. However DTL chips are nearly impossible to find today. The only thing to be careful about is old DTL based designs often used wired-and gates (i.e. directly tying outputs of several gates together to reduce part count). You cannot do this with normal TTL!


What are the typical switching voltages that may be applied to the inputs of a PLC?

Look on the datasheet. But most are either TTL compatible (0V to 5V) or low voltage TTL compatible (0V to 3.3V). Some have open drain outputs that can handle higher output voltages by using a pullup resistor.The important thing is always consult the datasheet to know for certain on a specific device.


What are the compatible features of the Yongnuo YN685 flash for Nikon cameras?

The Yongnuo YN685 flash is compatible with Nikon cameras and features TTL, HSS, and wireless triggering capabilities.


Why an open ttl gate behaves as a logic high input?

because TTL have a bias input setup to eliminate noise therefore the output will follow the logic one input if left open


What are the features and compatibility of the Insignia TTL external flash for Canon cameras?

The Insignia TTL external flash for Canon cameras features automatic TTL metering, manual control options, and a guide number of 42. It is compatible with Canon EOS cameras and offers versatile lighting options for photography.


Interfacing of ttl with cmos and cmos with ttl?

whis is Endurance mors or ttl


How can a ttl output from a receiver be used to switch a transistor on or off?

By choosing the type of transistor to meet your needs carefully. I assume what you're trying to do is feed beyond the ttl output's power capability? a JFET may be a good option. A simple amplifier circuit using a MOSFET may be all you need, and this might be more readily available.


What is conversion of TTl voltage level to MOS level?

A: TTL Vcc is fixed at 5v +/- .5 volts while MOS can be run at higher Vcc like 12 volts therefore there is a compatibility problem and a converter must be installed between this family of gates to make them compatible with each other. So a converter will do just that translate a TTL level to a MOS level