0
If your New Holland 310 square baler is not tying twine, it could be due to a few common issues. First, check the twine tension and ensure that the twine is threaded correctly through the tying mechanism. Additionally, inspect the knotters for any debris or damage, as well as the tension on the knotter springs. Lastly, ensure that the baler's drive system is functioning properly, as a lack of power could hinder the tying process.
What else can I help you with?
How do you thread the twine on a New Holland 273 baler?
To thread the twine on a New Holland 273 baler, first, ensure the baler is turned off and safely positioned. Start by opening the twine box and placing the twine spools onto their holders. Then, guide the twine through the tensioner and around the twine guides, leading it towards the knotters. Finally, thread the twine through the knotter mechanism as per the baler's manual instructions, ensuring it is properly secured before closing the twine box.
What IH baler had the twine box on side of baler?
The IH Mccormick 50, 55, and 45 balers all had twine boxes on the sides of chute on the rear of the baler.
What makes the string cut on a hay baler?
A blade cuts the twine as it finishes wrapping
How do you make a tight square bale using a Massey Ferguson 124 square baler?
run the twine through the eyelets and through the needles , which are the large arms that rise up . take that twine and tie to the rear of the baler,both of them and run them where the bale forms. next trip the wheel that ties the bale, and turn the baler by hand for one cycle. the twine will be tied now cut the excess twine that u tied to the rear of the baler from the needles and you are ready to bale .
How do you thread a 270 hay baler?
To thread a 270 hay baler, first, ensure the baler is properly set up and the twine is loaded onto the spool. Pull the twine from the spool and guide it through the tensioner and around the bale chamber, following the specific threading path indicated in the owner's manual. Make sure to secure the twine in the appropriate clamps or guides to ensure it feeds correctly during operation. Finally, test the mechanism to ensure the twine is properly threaded and ready for baling.
Will a Massey Ferguson 12 baler take plastic string?
I have a model 12 MF baler, and I use the plastic twine all the time with no problems. Don in Oregon
How does a hay baler work?
hay is picked up by a the pickup tines, then pushed perpendicularly by a "fork". it is then compacted into slabs by the plunger and tied with twine by the knotters. the bale then comes out the back of the baler.
How do you thread a McCormick IH Forty Six baler?
THREADING THE TYING MECHANISM for a McCormick No. 46 Baler Open the door on the twine chest and place balls of twine in twine containers. There is room for 4 balls, 2 for each side. From left to right, as you look from the back of the baler, they will be referred to as balls D, C, B & A. Connect the inside end of ball "A" to the outside end of ball "B" connecting the two balls of twine in the right twine container. Connect the inside end of ball "C" to the outside end of ball "D" connecting the two balls of twine in the left twine container. If twine is taken from the wrong end of a ball, it will twist and snarl in the tying mechanism. Join the twine ends with a firm square knot. Trim the loose ends about one-half inch from the knot and you're ready to thread the tying mechanism. Make sure the needles are in their extreme rearward position. If they are not, turn the flywheel and power take-off drive by hand until the needles reach the extreme position of their rearward stroke Thread the twine from the inside of ball "B" through the grommet in the right partition and the center guide in the top of the left compartment of the twine chest. Thread the twine from the inside of ball "D" through the lower guide in the left compartment of the twine chest. Thread the twine balls "B" and "D" through the grommet in the left partition of the twine chest. Thread the twine between the pressure plates of the twine tension device and through the grommet in the bottom of the twine chest. Run the twine through the twine guide on the needle tie pipe and through the three twine guides underneath the bale chamber. The twine from the right twine container furnishes twine for the right needle and the twine from the left twine container furnishes twine for the left needle. Thread the ends of the twine through the holes of the needle head. Pull these two twine ends up through the bale chamber. Operate the baler slowly under power. Hold the twine as shown in Illust. llA (I tie it off to something near the back of the baler). Trip the clutch, and let the tying mechanism go through a cycle. Strip the single knots off the knotter hooks to complete the threading operation. Operate the tying mechanism several times at rated engine speed to be sure it is working smoothly. Hold the twine by hand each time to prevent the twine from fouling in the knotters.
How do you thread international 430 hay baler?
Twine comes out of the twine box, through the tensioner, through a couple of ceramic rings then 1 piece of twine through each needle eye. Once through the needle eye it goes back along the chamber floor and tie it off to something sturdy. The baler will thread the twine into the knotters at the first cycle. A common problem on old balers is the needle eyes have grooves warn in them. You should use a round file to file out the groove so the twine has a smooth surface to run over. A rough surface will cut the twine.
How do you thread tie arms on hesston round baler 5580 wont cut twine?
If the twine isn't cutting on your Hesston round baler 5580, first check the tension on the twine arms to ensure they are properly adjusted and not too loose or tight. Inspect the knife and cutting mechanism for wear or damage, as a dull or broken knife can prevent smooth cutting. Additionally, ensure that the twine is threading correctly through the arms and is not tangled or misaligned. Lastly, verify that the twine itself is in good condition and not frayed or too old, as this can affect cutting performance.
How do you you thread a new holland 310 hay baler?
Place two rolls of twine into the twine chamber, pull the end of the twine from the center of the rolls. Thread the twine from each roll through the loops in the lid of the twine chamber. Each twine should go through the loop on the side of the lid that the roll of twine sits on. The left side through the left loop, the twine on the right side through the right side loop. Run the twine through the two tubes on the left side of the twine chamber. The again, the left through the left side, the right through the right side. Close the lid to the twine chamber. Run the ends of the twine through the porcelian electric insulator fastened to the needle carriage, then the ends of the twine through the eyes of the needles. Again, the twine from the left side through the left needle eye, the end of the twine from the right side through the eye of the right needle. Pull the ends back to the protective pipes surrounding the needles and tie the ends to the pipe. Raise the bale trip lever on the drivers side of the bale chamber so it will trip shortly after you power the baler. You will need a small amount of hay going through the chamber to do this. When the bale trip lever trips, the needles will come up and the knotters will grab the twine and hold it. You are now ready to bale.
What kind of twine does a John Deere 24T baler take?
All I know for sure is our 24T uses 9000' rolls. One source of twine I uses is Tractor Supply Company...see the related link...
