0
What else can I help you with?
What is voltage phase to phase 380 3 phase?
Voltage phase to phase in a 380V 3-phase system refers to the voltage measured between any two of the three live conductors in the system. In a balanced 3-phase system, the phase to phase voltage is equal to the line voltage, which is 380V in this case. This voltage is commonly used in industrial and commercial applications to power heavy machinery and equipment. It is important to note that the phase to phase voltage is higher than the phase to neutral voltage in a 3-phase system.
Why do you have voltage to ground but not voltage phase to phase?
There is phase to phase voltage in 3 phase system.AnswerYou don't get voltage 'phase-to-phase'; it's 'line-to-line'!
In a 3 phase 480 panel what voltage should you get phase to phase?
The voltage you are referring to is a 'line-to-line' voltage ('line voltage'), as there is no such thing as a 'phase-to-phase' voltage.480 volts. In real life, the voltage will vary slightly by up to 3% (14 V) on a properly sized circuit. Line to neutral will measure 277 volts, plus or minus 3%.
What is 3 phase voltage in Germany?
Three-phase voltage in Germany is 400V, single-phase voltage is 230V.
What is the 11kv phase to earth voltage?
6350.8 volts AC rms. The phase to earth voltage is ( square root(3) ) x lower than the phase-phase voltage on a 3 phase system.
How do you convert 440 voltage line to voltage phase?
To convert a 440V line voltage to phase voltage in a three-phase system, you divide the line voltage by the square root of 3 (approximately 1.732). This means the phase voltage is calculated as ( V_{phase} = \frac{V_{line}}{\sqrt{3}} ). For 440V line voltage, the phase voltage would be approximately 254V.
How does a 3-phase 115 volt power supply measure 200 volts in-between each phase?
You should have about 230 volts between any pair of 3-phase service legs: L1-L2, L2-L3, L3-L1. If the voltage measured between any one pair results in low or no voltage, then you have a fuse or circuit problem.
What is 3 phase voltage in Iran?
The three phase voltage is 380 the hertz is 50
What is peak voltage value of 3 phase?
The same as in single phase with the same RMS voltage.
Why is three phase voltage 400 V when single phase is 230 single phase 1.73 3 phase. what is 1.73?
I will try and make this as simplified as possible. The secondary side of transfomers are connected in star - which means there is a neutral / earth connection. If you measure between a LINE to LINE ('line voltage') voltage you will measure 400V, but now we have introduced the neutral / earth and we measure between LINE to NEUTRAL ('phase voltage) 's LINE to EARTH we will get 230 V. The reason for this is that, because the phase voltages are displaced, in time, by 120 electrical degrees, you must add them vectorially to obtain the line voltage. And the vectorial sum of two 230-V phase voltages, displaced by 120 degrees, is 400 V -or 1.732 times either of the phase voltages.
If in the three phase connection phase to phase voltage is 400v what will be the phase neutral voltage?
The formula to use is, phase voltage /1.73 = phase to neutral (ground) voltage.CommentThere is no such thing as a 'phase to phase', or 'phase to neutral' voltage. The correct terms are 'line to line' and 'line to neutral'. So the above answer should read: line voltage/1.73= line to neutral voltage = phase voltage.
How do you convert line current to phase current?
The current is the same in the three live wires. The voltage can be described as the line voltage (phase to neutral) or the phase voltage (phase to phase) which is larger by a factor of sqrt(3). So a line voltage of 230 v corresponds to a phase voltage of 400 v.
