0
If your Laars 2 heater pilot won't stay lit after releasing the button, it may indicate a faulty thermocouple or a problem with the gas supply. The thermocouple is responsible for sensing the pilot flame and keeping the gas valve open; if it's defective, it won't allow the pilot to stay lit. Additionally, check for any blockages in the gas line or ensure that the gas is turned on. If troubleshooting doesn't resolve the issue, consider contacting a professional technician for further assistance.
What else can I help you with?
How to light a gas heater with an electronic pilot?
To light a gas heater with an electronic pilot, locate the pilot light button on the heater. Press and hold the button while simultaneously pressing the ignition button. Keep holding the pilot button for about 30 seconds to allow the pilot light to ignite. Release the pilot button and adjust the temperature as needed.
What if the pilot on your teledyne laars epg 250 pool heater will not stay lit and you have just replaced the pilot generator?
Check that you are getting voltage from the thermocouple. You should see about 600 millivolts.
Why does your teledyne laars phase 2 pool heater not ignite?
Possible reasons why a Teledyne Laars Phase 2 pool heater may not ignite include issues with the pilot light, gas supply, or faulty igniter. Check if the pilot light is lit, ensure there is proper gas supply to the heater, and inspect the igniter for any signs of damage or malfunction. Additionally, check for any error codes on the heater display panel that may provide further information on the issue.
How do you light the pilot on a wall heater?
To light the pilot on a wall heater, locate the pilot light button or knob and turn it to the "pilot" position. Hold down the button or knob while using a long lighter or match to ignite the pilot flame. Keep holding the button or knob for about 30 seconds to allow the pilot to stay lit. Release the button and adjust the temperature as needed.
How to light a water heater with an electronic pilot by Honeywell?
To light a water heater with an electronic pilot by Honeywell, follow these steps: Locate the control panel on the water heater. Turn the control knob to the "Pilot" position. Press and hold the pilot button while pressing the ignition button. Continue holding the pilot button for about 30 seconds to allow the pilot flame to ignite. Release the pilot button and turn the control knob to the desired temperature setting. Always refer to the manufacturer's instructions for specific details on lighting your water heater.
How can I relight the water heater pilot?
To relight the water heater pilot, locate the pilot light button or knob on the water heater. Turn it to the "pilot" setting and hold it down. While holding the button down, use a long lighter to ignite the pilot light. Keep holding the button for about a minute after the pilot light is lit to ensure it stays on. If the pilot light continues to go out, there may be an issue with the thermocouple that needs to be addressed by a professional.
How can you get the pilot light on a teledyne pool heater to start if you have pressed pilot and the red button?
sit on it then throw it into a creepy cave
What are the steps to relight the pilot on a hot water heater?
To relight the pilot on a hot water heater, follow these steps: Locate the pilot light assembly on the water heater. Turn the gas control knob to the "off" position and wait for at least 5 minutes. Turn the gas control knob to the "pilot" position. Press and hold down the pilot button while using a long lighter to ignite the pilot light. Continue holding down the pilot button for about 30 seconds after the pilot light is lit. Release the pilot button and turn the gas control knob to the desired temperature setting. Remember to refer to the manufacturer's instructions for specific guidance on relighting the pilot on your particular water heater.
How do I turn on the water heater pilot?
To turn on the water heater pilot, locate the pilot light button or knob on the water heater. Turn the knob to the "pilot" setting and hold it down. While holding the knob down, use a long lighter to ignite the pilot light. Once the pilot light is lit, continue holding the knob down for about a minute before releasing it. This should successfully turn on the water heater pilot.
Why would burner pilot light extinguish shortly after firing up on Laars Lite Model LLG Pool heater?
Have the thermocouple checked or spillage from down draft and make sure there is free air for proper combustion
How do you light the water heater pilot?
Turn knob to PILOT, press button down and light the pilot; hold button down for 60 seconds and release - pilot should remain lit; turn knob to ON. If pilot does not remain lit, turn knob to OFF, wait 5 minutes and try again, If pilot still will not remain lit, replace the thermocoupler.
How do you turn on a gas heater pilot?
To turn on a gas heater pilot, first, ensure the gas supply is turned on. Locate the pilot light access and set the thermostat to the lowest setting. Press and hold the pilot button or knob while using a long lighter or match to ignite the pilot flame. Once lit, continue holding the button for about 30 seconds to ensure the thermocouple heats up, then release it and adjust the thermostat to your desired setting.
