0
The ideal salt level is between 2700-3400 ppm (parts per million) with 3200 ppm being optimal. Before adding salt to your pool, test the water to check your salt level.
What else can I help you with?
Can you use water softener salt for a pool salt system?
There are two types of salt based pool chlorinators. More expensive and less common are those with a separate salt tank and these will normally use tablet salt for water softeners. The more common type is where salt is added to the swimming pool itself. In the UK we most commonly use PDV salt - that is Pure Dried Vacuum Salt or table salt. Granular salt for water softeners can be used. Tablet salt for water softeners should be avoided unless you have a white liner, because the tablets may bleach spots on the pool liner before dissolving. Julian Hobday of KindWater.
How do salt levels in salt pool go up?
If you are adding salt to a salt water pool with a salt water chlorination system and the TDS level does not go up then the problem probably lies with the chlorination system not working (the electrolysis unit or power supply). Adding salt directly to the pool will increase the TDS (Total Dissolved Salts) concentration of the water.
What should be done if your Pool Service treats your salt water pool as a Chlorinated pool and adds chlorine shock to your salt water pool by mistake?
Get over it. He made a mistake. You may point it out to him nicely of course. BTW it does not hurt or he may have felt that the pool needed it. BTW there is a mode in the salt system to shock the pool thru the system. precipitation
Why does my Intex salt water pool system keep turning the water brown - goes into the system clear but water exits the system - and into pool - brownish?
Are you using iodized salt or pool salt? I've read that the iodine in the iodized salt will leave yellow staining in the pool.
What should the readings be for alkalinity and stabilizer for a salt water swimming pool?
The same as a non-salt system pool. Disregard answer above. The only reading that will remain constant, in the above situation, is the alkalinity =80 - 120 ppm; pH = 7.4 - 7.6 For a salt system pool your conditioner/stabilizer should be slightly higher than a namually fed pool. You should achieve readings of 75 - 85 ppm.
How do you size a pool saltwater system?
Salt systems are rated for the maximum size pool in gallons that they can maintain. This sizing only applies to a pool that is barely used and does not get much debris or sunlight. In all other pools you should go 1.5 times bigger on the salt system than the size of the pool itself. For example a 10,000 gallon pool will require a 15,000 gallon salt system. If the pool is used a lot or it gets plenty of sunlight and debris, or all three you should go twice as big.
How do you check the salt level in a pool?
You can buy salt test stripes at any local pool store or have them check it for you.
How much salt goes into a swimming pool?
It depends how many gallons your pool is. Once you buy your chlorinating system, the install manual will tell you how much salt to add based on how many gallons in the pool. I have an Autopilot Digital and it tells me when it needs salt. I still check it with test strips to be safe.
Will switching from chlorine chemical system to a salt water system ruin pool?
No A salt water pool is in fact also chlorine pool, the difference being that with a salt water pool a salt water chlorinator converts the salt that is in the water into chlorine gas which is then dissolved into the water while the filter is running. the conversion wont have any adverse effects on the pool.
Where can you get the salt from for your pool salt chlorinator system?
Most pool shops carry it and some department stores and hardwares
How do you reduce the salt levels in a salt generated pool system?
first you find out how much is required. there is a floating device that will tell you how strong the concentration of salt is. then you simply toss the required salt into the water, it will lay there for a while and slowly dissolve.
Will installing a saltwater system on a new pool immediately after filling with water but before the interior has cured stain the pool?
I have a salt water system and recently had my pool resurfaced. There was no staining. If you put your salt in the skimmer like you we're supposed to there should be no staining, If you put your salt directly into your pool it could stain from the minerals in the salt. If you used table salt there will be much less staining than if you used road salt. ANSWER:: You should NEVER use road salt or table salt. Wrong chemical make up! Follow directions on the "pool salt" bag. The salt goes into the pool and not the skimmer!! You must brush any salt that lingers on the floor until it is mostly dissolved. DO NOT add salt until the water has filtered for at least 24 to 36 hrs. or that recommended by the manufacturer or pool builder. Do not rely on other people to tell you what needs to be done. GO to the source -- builder - manufacturer. You should not have staining if the above basics are followed. Additionally, you must run the standard pool equipment for about 2 weeks or more. This gives the plaster time to cure properly. The salt system can and most likely be installed by the builder as he installs the pump and filter. The salt system unit will not be turned on until the plaster has cured. After the cure you must follow procedures on the proper start-up of the salt system. K
