answersLogoWhite

0

The link to the manual is below

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

How to replace a Toro weedeater pull string?

To replace the pull string on a Toro weedeater, first ensure the engine is off and cool. Remove the starter cover by unscrewing any screws, then take out the spool containing the old string. Thread a new string through the spool, wind it tightly in the direction indicated, and reassemble the spool into the housing. Finally, reattach the starter cover, and your weedeater will be ready for use.


How do you retread your task force weedeater model 21083?

To retread the Task Force Weedeater model 21083, first, ensure the weedeater is turned off and unplugged. Remove the spool cap and take out the old line, then cut a new line to the appropriate length—generally around 10-15 feet. Wind the new line evenly onto the spool, following the directional arrows, and reassemble the spool and cap. Finally, plug the weedeater back in and ensure it operates correctly before use.


What could cause a Weedeater trimmer spool to not spin if the motor runs and revs up nicely?

Take the spool off the the machine. By that I mean the part that contains the cutting line. There will be a spring that drives the spool. Get a pair of pliers and gently pull on it. If it comes out of the shaft it is probably broken or it came loose. If that does not solve the problem look at the spool where the nut is located make sure its there and that the housing is not wallowed out. If so buy a new spool.


How do you replace the line on a stihl KM56RC Weedeater?

To replace the line on a Stihl KM56RC Weedeater, first, turn off the engine and disconnect the spark plug for safety. Remove the cutting head by unscrewing the knob at the bottom. Take off the spool and unwind any old line, then cut a new line to the desired length (typically 10-12 feet). Thread the new line through the spool holes, wind it tightly in the direction indicated, and reassemble the cutting head before reattaching it to the Weedeater.


How do you install 065 cutter line on Weedeater model RTE 115 trimmer which you have only been able to find prewound spools at Lowe's?

Unscrew cap and remove. Remove line guide ring. Note which way to put line guide ring back on, slot to outer edge. Remove the empty spool. Don't take spool apart unless you need to get inside to remove string. The outer half should be yellow. Cut 25 ft. of .065 line. Start pushing the line inside the spool from the center making sure the string is winding inside in a counter clock direction which should be shown on the spool. Keep pushing until there is about only 6 in. left. Replace spool. Then the line guide ring, making sure to pull the string through the middle of it. Then hold the string on the slot in the ring while replacing the cap. You should be set to go.


How do you change the trimmer line on a Ryobi Expand-It?

To change the trimmer line on a Ryobi Expand-It, first remove the spool cover, then take out the spool and replace the trimmer line following the arrows on the spool. Finally, reassemble the spool cover.


What is the take off for a six pipe spool?

6"


Feeds thread from spool to needle?

The thread moves from the spool through the needle to make stitches on a sewing machine. The thread take-up lever is what feeds the thread from the spool to the needle as it moves up and down.


How do you remove the trimmer head from weedeater SST25?

stick a flat head screw driver in the slot above head and turn counter clock wise.


How to spool Black and Decker grasshog weed trimmer?

To spool a Black and Decker Grasshog weed trimmer, first, unplug the trimmer for safety. Open the spool cover by pressing the tabs or using a screwdriver, then remove the empty spool. Take a new spool of trimmer line, thread the line through the eyelet and wind it around the spool in the direction indicated by the arrows, leaving a few inches free. Finally, reinsert the spool into the trimmer, pull the line through the exit port, and close the spool cover securely.


How do I replace the line on my Ryobi line trimmer?

To replace the line on your Ryobi line trimmer, first, remove the spool cover and take out the spool. Cut a length of new trimmer line, thread it through the holes on the spool, and wind it evenly. Reassemble the spool and cover, and you're ready to trim.


How to change the line on a Ryobi weed eater?

To change the line on a Ryobi weed eater, first, remove the spool cover and take out the old line. Cut a new line to the correct length and insert it into the spool. Wind the line evenly and securely onto the spool, then reassemble the spool cover.