0
What are the damper pulley bolt tightening specs on a cat C15 engine?
Wiki User
∙ 9y ago
The damper pulley bolt tightening specifications, on a Caterpillar see 15 diesel engine, is 60 pounds per square inch. The pulley should not be tightened beyond 60 pounds.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
What are the head bolt torque specs for a Cat 3024?
The head bolt torque specifications, for a Caterpillar 3024 diesel engine, is 170 pounds per square inch. The bolts should be tighten at 50 pound intervals.
What are the torque specs for a cat c15 4 bolt connecting rod?
The Caterpillar C15 diesel engine torque specifications for the rod bearings is 35 pounds. The main bearing torque specifications is 350 pounds.
What is it that everyone always overlooks?
there own nose.
What does a Hoopoe look like?
A hoopoe has a long, flat black bill. It has a very distinctive crest which includes long reddish feathers with black tips. It's wings are also multi-colored with black specs over red feathers. Check out a photo at the link below in Related Links.
What bird egg is white with black specs?
Oystercatcher birds lay white eggs with black speckles. Oystercatchers typically lay between one and four eggs. These birds are known to practice "egg dumping", which is where they lay their eggs in the nest of another bird, leaving the other bird to raise their young.
On a Chevy 350 crank pulley there are three outer bolts and one center bolt - what should they be torqued to?
the center bolt is for the harmonic balancer , aka , vibration damper or torsional damper . the torque specs. i have are 1985 and before 60 ft-lbs , 1986 to 1995 70 ft-lbs , 1996 and later 74 ft-lbs . can't find any specs. for the pulley bolts .
What are the engine torque specs and tightening patterns for a 1968 327 camaro engine?
plugs 25 ft lbshead 65 ft lbsintake 30 ft lbsexhaust 20 inch lbsrocker cover 55 ft lbsconnecting rod3/8 bolts 45 ft lbs11/32 bolts 35 ft lbsmain bearing 80 ft lbsflywheel 60 ft lbsvibrtion damper or pulley 60 ft lbs All of these are taken straight from my old MOTORS manual. Hope it helps Kathy
How to replace intake manafold on V6 3800 engine?
Ineed the torque sequence and tightening specs for a 92 GM 3800 intake.
What is the torque and tightening specs on 1999 4 0 ford engine overhead valve?
If you need the torque specs for every single bolt in that whole engine, that is a pretty tall order. Or are you just needing one particular part of the engine, like the head bolts?
What are the torque specs for a 22r head?
get specs from your local librarys technical isle look up specs and tightening sequence.
What are the torque specs for a 1987 Chevy S-10?
For the 1987 Chevrolet S-10 with a 2.8 liter engine, the torque specs for the cylinder head bolts is 40 ft. lbs. The torque specs for the crankshaft damper bolt is 70 ft. lbs. For the oil pump bolts and the oxygen sensor, the torque is 30 ft. lbs.
What was the 1947 Ferrari's performance and engine specs?
the engine specs is tat it runs on poopys
What is the Jeep Liberty lug nut spec?
The correct tightening specs for your liberty is 100 ft lbs.
What are the torque specs for a 1996 Chevy s10 4.3 liter?
For the 1996 Chevy S-10 4.3 liter, the torque specs for the crankshaft damper bolts is 70 ft. lbs. For the cylinder head bolts, the torque is 65 ft. lbs, and for the engine mount-to-head bolts, the torque is 35 ft. lbs. For the engine mount-to-frame bolts, the torque is 52 ft. lbs.
What is the timing specs 1996 Ford F-250 5.8 engine?
timing specs 96 5.8 engine
1994 fxrp engine specs for motorcycle?
1994 harley Davidson cop bike, i need engine specs
How do you replace a Saab 900s oil pump?
What year? Which engine? Generally, the oil pump is located on the front of the engine, behind the crankshaft pulley. 1) Lock the flywheel in place. 2) Remove the accessory belts and crankshaft pulley. 3) Remove the oil pump. A workshop manual will aid greatly in providing proper endfloat specs and special re-assembly instructions for the particular engine.
