answersLogoWhite

0

Head bolts should be tightened most of the way in a star-shaped pattern. Bolts should then be tightened completely following the same pattern as the first tightening.

User Avatar

Wiki User

11y ago

What else can I help you with?

Related Questions

What are the cyl. head bolt torque specs for a KIA 1.8 L 2000?

Hello: Install cylinder head bolts. Tighten cylinder head bolts according to following procedure: Tighten cylinder head bolts in order shown, Can not show diagram for this. Tightening torque : 36.1 lb-ft (49N


Head bolt tightening sequence for Mazda e2000?

Begin by tightening the head bolts on each corner of the head. Next, tighten the center head bolts. Tighten the bolts on each end of the head and move towards the center.


What is the function of an Allen wrench?

To tighten and loosen Allen head bolts


How tight and in what order do you tighten the head bolts on a Vortex small block 350 V8?

Tighten from top to bottom and from front to back...80 lbs of torque.


Can you tighten the head bolts On a 91 prelude without pullng the cams?

no as there are head bolts directly under the cam i belive


1998 Mazda protege cylinder head bolts torque you bought haynes manual and it tells you torque head bolts to 1215lbs then tighten 45degthen 90deg what you need to know do you turn bolts 45then another?

Many of the newer head bolts are tightened all bolts to a specific torque spec then tighten all bolts another 90 degrees or whatever the manufacturer recommends and possibly even another step. The idea is to tighten in stages so that you do not warp the head.


What is the torque for the head gasket of a '93 dodge shadow and what is the order to tighten the bolts?

10 6 1 2 7 9 5 4 3 8 tighten in that order when tightening turn one quarter turn then torque to 65 in that above order and then tighten to 65 in that order again


What are the torque specifications for Subaru EJ25 cylinder head bolts?

According to the manual for a EJ25 SOHC:Bolt sequence:____| C A F || E B D |-----B: INSTALLATION1) Install the cylinder head and gaskets on cylinder block.CAUTION:• Replace cylinder head gaskets with new ones.• Be careful not to scratch the mating surface of cylinder block and cylinder head.2) Tighten the cylinder head bolts.(1) Apply a coat of engine oil to the washers and bolt threads.(2) Tighten all bolts to 29 N·m (3.0 kgf-m, 22 ftlb) in alphabetical sequence.(3) Tighten all bolts to 69 N·m (7.0 kgf-m, 51 ftlb) in alphabetical sequence.(4) Back off all bolts in reverse order of assembly by 180° first; back them off by 180° again.(5) Tighten bolts A and B to 34 Nm and bolts C-D-E-F to 15 Nm(6) Tighten all bolts by 90°(7) Tighten all bolts a further 90°CAUTION:Do not tighten bolts more than 90° in total angle


Cylinder head torque settings for a 1997 punto s 60?

Head bolts for a Punto 60s need to be tightened in 3 stages: stage 1 - tighten all bolts (in the correct order!) to 30Nm. stage 2 - tighten again, in same order as before, by turning wrench a further 90 degrees stage 3 - repeat stage 2


Honda d15b2 head Tightening Sequence?

The Honda had bolt tightening sequence begins with the head bolts on each end of the head. Tighten the head bolts moving to the center, alternating from and to end.


Are flare nut wrenches used to loosen or tighten cylinder head bolts or are they used to loosen or tighten fuel line fittings?

Flare nut wrenches are used on fuel lines. Regular sockets are used on head bolts.


What is head bolt pattern for 2006 4.7 liter Dodge?

he cylinder head bolts are tightened using an angle torque procedure, however, the bolts are not a torque-to-yield design. 6. Tighten the bolts in sequence using the following steps and torque values: Step 1: Tighten bolts 1-10, 20 N·m (15 ft. lbs.). Step 2: Tighten bolts 1-10, 47 N·m (35 ft. lbs.). Tighten bolts 11-14, 25 N·m (18 ft. lbs.). Step 3: Tighten bolts 1-10, 90 degrees. Tighten bolts 11-14, 30 N·m (22 ft. lbs.).