What would you like to do?
Well you narrowed it down to an electrical problem, get yourself a dmm and start chasing wires. I've also seen a bulb burn out and short causing the fuse to blow when t…he brake pedal is depressed. double check your fuse again and if its still good have at it with the digital multimeter.
How do you change the light bulbs in the turning signal and brake lights for a 1996 Ford Thunderbird?
If it's anything like my 92 bird, to replace the signal lights you just pull back the carpet in the trunk and twist the deal that holds the bulb then pull it out. … What if the bulb has broken or shattered but is still installed in the socket??
pull back the carpet take the plastic panelthere should be 2 skrews take them off and then pop the lense out
Answer It depends on the type of vehicle that you are workin on. Most cars brake light housing screws are located inside the trunk. These are accessable b…y opening the trunk. All you have to do is unsrew the screws or bolts that hold the cover in place, locate the bulb that is burned out and twist open the plug from the rear or pull the bulb from the front and replace it.
I also have a 2001 focus wagon and had a little trouble finding how to change the rear bulbs. Jim was right. On this model (I don't know for other model of focus), there are o…nly 2 Philips screws to remove. There is NO plastic thumbscrew to remove from inside (if you have a different model, for instance a ZX3, verify if there is such a thumbcrew accesible from the trunk). No need to access anything except the 2 Philips screws. I swear! So you remove the 2 Philips screws (I did it with a key!), then you GENTLY tilt the lense cover in a direction opposite to the trunk. That's the key. Don't pull on the cover, but tilt it with respect ot a vertical axis. There is a clip in the innner side that will be released, and then you simply move the cover laterally to free the 2 pins that Jim was talking about. It might seems to be be stuck at first due to the dirt that have accumulated on the seal. In this case, push firmly while still retaining the cover to prevent an excessive rotation that could break the plastic pins integrated to the cover. If you're no sure, try on the other side, which could be easier to remove and let you see how it made behind the cover. You can do it!!! j-nic
Answer Usually through the back panel in the trunk
Open the rear hatch door. 1. Remove the 4 screws holding the lens assembly to the vehicle. It may have a silicone or a sealer holding it in place, so if it does, slowly pull… the assembly towards you as you cut away anything holding it in place after the screws are removed. 2. You can now remove the bulb assembly by holding firm the lamp assembly and twist counter clock wise the bulb socket then pulling straight out from the lamp assembly. 3. To remove the bulb socket from the lamp assembly, push in on the bulb, and twist it clockwise while pulling on it. The bulb should now be removed. 4. Insert new bulb, twist clockwise to lock it into place. 5. Insert the bulb and socket assembly into the lens assembly and twist the socket clockwise to lock it. 6. Reinstall the lens assembly, then tighten lens assembly screws. Test lights.
When you open the hatch back there are two screws, take that off and then pop off the light cover and it is there.
Unscrew the light from inside the van and remove the light from the outside
The focus of this project is changing the right-hand (RH) brake light on a 2005 VW Beetle TDI (although the same steps can be used for the left hand side, as well …as on several other VW models). The rear tail light bulb is accessed by removing the lens housing cover located in the trunk of the vehicle. Following the below steps, you will be able to replace the tail light bulb yourself and save $100 in professional repairs.
depending on what side it is, you need to take off the plastic panel, this will give you access to the bulb cluster. there is a small clip you need to push down, then the bulb… cluster will come out....should take you about 5 minutes
Trunk open, remove the 4 wing nuts on the casing. The casing will pull off from the outside. The bulbs are in there.
In the back, directly behind the lights, the trim must be removed.( There will be some clips or screws holding the carpet or plastic in place). once removed you will see the b…ack of the lights, then its just a case of removing the blown bulb and replace a new one and fitting back the trim......
In Ford Fiesta
Step 1: Remove the two screws on the rear of the car that secure the light housing (as per the manual) Step 2: Ignore everything else the manual says. Pull out the light hous…ing and you will see a plug connecting the electrics to the housing. Lift the retaining clip on this and remove the plug. The entire housing should now be disconnected from the car. Step 3: On the rear of the housing is some white plastic, this holds all the bulbs. Remove the plastic by lifting the two retaining clips. The Bulb holder will now lift clear of the housing completely. The brake light is the top bulb. Hope this helps :-)
You will need a new central mounted brake light bulb for your vehicle. Changing it is very easy. You just need to pull the old one out and push the new one in.
Purchase the correct replacement bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Its recommended to repl…ace both left and right at the same time in order to keep brightness and color equal (optional). Then consult your owner's manual for the replacement procedure.
1999 Ford F-250 brake light bulb replacement: Purchase the correct replacement brake light bulb(s) first, before disassembling the vehicle. See sources and related links below… for replacement brake light bulb information. Then consult your owner's manual for the replacement procedure. As simple as it sounds, the owner's manual is the best place to start for brake light bulb replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).