0
your resevour should be on the drivers side under the hood. the valve to release presure is under the truck on the driverside as well. the process is messy and you will need 2 people but you just fill your resevour with dot 3 brake fluid and pump the clutch about 7 or 8 times and hold the clutch in while you release the presure. then release the clutch refill and repeat. i went through about 2 1/2 big bottles of brake fluid and about 3hrs of work before i got all the air out. good luck.
Wiki User
∙ 8y ago
Add your answer:
Earn +20 pts
How do you bleed the air in your clutch line on a 1997 gmc sonoma?
same as bleeding the air in the clutch line for any other car -stab the air.
How do you bleed the Mercedes c180 clutch?
You can bleed the clutch by loosening the fluid line. With the line loose pump the brakes until fluid comes out.
How do you bleed the clutch line on a 2004 ford ranger edge?
how do I bleed the clutch system in a 2004 ford ranger
Leak in the cab of your 1991 Ford Ranger coming from the clutch What should you doshould you replace the entire clutch or is it just the line?
Replace clutch master cylinder and bleed system,also check your slave cylinder for leaks.its bolted to your transmission,the clutch cable is connected to it.
What is the cause of a 97 elantra clutch pedal getting completely stuck?
You need to bleed your clutch master cylinder line.
How do you adjust a clutch on a 1987 Pontiac Fiero?
There is no clutch adjustment. The clutch is hydralic and therefore needs no adjustment. If the clutch isn't working correctly you most likely have to bleed the clutch line.
The clutch pedal on your 89 240sx sticks to the floor it has a new clutch what do you do?
Bleed the slave cyl. It probebly has air in the line or no fluid.
Where is the clutch bleed nut on a jeep yj?
Look at the same location as the clutch line going into the trans, but on the other side ( passengers side ) the bleed valve will be on a line exiting the bell housing top passengers side. Remove the access panels around your shifter and you will see them both, and another nifty thing is that with it right there you can bleed the clutch without help.
How do you adjust a hydraulic clutch on a 1989 jeep--- what i mean is you have to push the clutch all the way to the floor to change gears. is there air in the line is there a way to bleed the line?
hydraulic clutch does not have adjustment. replace the clutch it has a slave cylinder underneath and what you do is pump up the clutch and then hold it and have somone turn the line going itno th slave cylinder until you have clear fluid that is not how you bleed a clutch to the jeep owner, if you know how to bleed brakes on a vehicle, then you know how to bleed the clutch on a vehicle both done the same way.now if no parts of the clutch, such as master or slave cylander have been touched or let run out of fluid, there is still no need to bleed as that will not be the problem you might look at the linkage on the slave cylander. sometimes there is nylon bushing on the cylander rod that wears out. replace this bushing which is easy to do and your clutch will be good again.
On a 1990 Isuzu Amigo what would cause the clutch pedal to stick to the floor?
if its hydraulic there could be air in your line. bleed your clutch and refill.
How do you bleed a clutch on opel astra gtc?
Follow the clutch hydraulic line down to the bell housing. Note where the hydraulic line goes into the bell housing and if there is no bleed valve there you may need to remove a cover. Have a friend/assistant step on the clutch while you open the bleed valve. Close the valve and have the friend let up on the clutch. Do that a few times (making certain that the hydraulic fluid remains full) and you're done.
What do I do after installing new clutch 2005 corolla xrs the clutch pedal seems super free to push in also having a rough time moving in and out of gears as if misaligned?
Bleed the clutch line that runs from the clutch master cylinder to the slave cylinder utilizing the bleed valve on the slave cylinder.
