0
The padding is simply stapled to the subfloor in most cases. If it is stapled down, just rip out the padding in pieces as large as possible. There will be small pieces of padding still stuck to the staples. Now you can either pull up the staples one by one using a staple remover (this will take a long time) or there is a scraper tool you can buy at home improvement tools that you can scrape along the floor to remove the remaining staples and padding.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How do you get diarrhea smell out of carpet?
You may have to remove the carpet pad as well. If it was contaminated, it will have to be replaced, as it cant be cleaned. Just cut a replacement piece to fit, clean both sides of carpet, let dry, and re tuck the carpet.
Can you glue carpet to the pad?
Carpet is not supposed to be glued to the pad, and I really can't imagine what advantage that would give you.
Should sponge rubber carpet pad be stapled or glued?
Gluing splices is the common way to lay pad for carpet.
Can you leave baking soda on carpet pad for good under the carpet?
Yes
How important is it to get a thicker pad under my new carpet?
It depends on where the carpet is installed. You want a thinner pad on high traffic areas. A thicker pad will give a softer, more luxurious feel.
Can you use peel and stick carpet over carpet padding?
No, the carpet pad moves far to much and your tile will look loose and crooked in a very short amount of time. Also, the carpet pad will not allow the adhesive to bond to it.
How much does it cost for carpet and installation of a room 91.5 by 11.5 feet a lower grade carpet?
$1550 uninstalled with pad, $2025 installed with pad
How do you install carpet on a tiled floor?
Get a tile cutter and remove the tile. Strip all the tile off and make sure the underneath surface is clean. Then u install a protective foam pad layer and install the carpet above it.
How do you remove sick smell from carpet?
You can either remove your carpet and add a new one, or wash the carpet
How to Install a Carpet Runner?
A carpet runner can brighten up your home when placed in a strategic location such as a hallway, entry way or stair case. Installing a carpet runner can be simple provided that you have the correct tools and know how. To properly install a carper runner, you will need carpet padding, a razor blade, hammer gun/staple gun, straight edge, ruler, pad tape and for stair installations, an electric staple gun.1.) The first step in installing a carpet runner is to measure the area of the installation and map out the placement of the runner, using your straight edge as a guide. This will help to ensure that the carpet runner will be placed in its desired location.2.) Once the measurements have been completed and the placement has been mapped out, deduct an inch from the length and width of your measurements and use your razor blade to cut the carpet pad to that size.*Note: if you are installing your carpet runner on steps, the pad should only go on the tread of the steps, not the riser. Measure your pad to come out to the edge of the nose and a 1/2 gap should be left at the crotch of the step for stapling.3.) If there are any seams in your cut to size carpet pad, join them with pad tape.4.) Using your hammer gun/staple gun, secure the carpet pad in place, ensuring that the pad stays straight and that there is a half inch gap between the edge of the carpet pad and where the edge of your carpet runner will lay.5.) Roll the carpet runner out on top of your carpet pad, ensuring that it remains straight and centered.**If this is a hallway or entry way application, you are done!6.) If you are installing a carpet runner on stairs, you will now need to staple the carpet runner to the stairs with an electric staple gun. Staple the carpet to the nose and crotch of the stairs, ensuring that the carpet remains tight against the stairs.7.) Enjoy the beauty your new carpet runner has brought to your home!
What kind of pad do I need to cover tile floor with carpet?
You should get a thin pad that can provide cushioning when covering your tile floor with a layer of carpet. This is so that the carpet can be placed evenly on top without having the grooves of the tile show through
Do you need a moister barrier if you install carpet over linoleum no pad?
No, you do not.
