0
A broaching tool - or a reciprocating machining process such as a shaper, see the link in the resources below.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What is a keyed shaft?
A keyed shaft or Keyway is method, based on a machined keyway in shaft, to attach something to the shaft and associated bore. A fitted key is inserted into a slot that is machined into the shaft. Although a machined keyway does result in a weaker shaft, it has it's applications. As in a lawn mower engine shaft. Theoretically the key will give way and save the shaft if you hit something with the blade. The negatives of a keyed shaft are that it can be deformed over time and result is a loose drive.
When was Keyway Air Transport created?
Keyway Air Transport was created in 1986.
What is the purpose of a keyway in a slab on grade?
The purpose of a keyway is to stop the movement of the foundation.
Is the keyway on a small block Chevy at 0 degrees?
This is a good question. Yes, the keyway, is accurate. What is not, is the balancer. After 74, the balancer keyway is offset, from the timing mark. Any harmonic balancer you use, look to see where the keyway is, compared to the hash mark on it. Make sure they line up.
Where was the keyway invented?
in Glasgow i think
Why would the pulley to the block of a car not be moving?
clear as mudpullies are normally attached to an engines crank either by being directly bolted to the nose of the crank which has a taper machined into it and is retained by the pressure exerted by the attaching bolt which screws into the nose of the crank. The other method is to fit the pulley over the crank nose which has a valley or keyway machined along about an inch or so along the length of the nose and then place the pully onto the crank nose and line up a corresponding machined keyway in the pully and insert a metal key into the space created by the keyways. pullies will remain stationary if a key fails or is sheared,or if the pully bolt has fallen out and the pully has become loose on a tapered crank or the other cause is when the rubber dampener which circles the mid section of the pulley perishes thru from contamination by fuel and oil etc the crank continues to rotate with affecting the pulley. so there,it is ,clear as mud. razmo ANS 2 -If this pulley is not moving, the crankshaft is not turning.
How do you put a go kart clutch on?
to put the clutch on omn side of the motor theres a crak and you to the clucth on there then put the keyway in the slot or you dont have to if the clucth has a biuld in keyway
Remove the torsion bar in a dodge ram?
Jack the front end up and support it w/jackstands. You can either use a torsion bar unloading tool or rent a ball joint press which is what I did, and place it around the crossmember to where the keyway or "porkchop" is located. Apply presure to the keyway by screwing the balljoint spacer as if you were tightening it. This will relieve the pressure off the keyway adjustment bolt so you can unscrew it and take out the keyway bolt keeper. Next unscrew the ball joint press and the keyway will fall lose. Then you can pull the torsion bar all the way through to remove it.
Where are the timing marks on cam gear on a 3.1v6 Chevy Lumina 91?
the timing marks are not on crankgear on cam gear Chevy Lumina 3.1 1995 would it be keyway to keyway
What are the ratings and certificates for Machined - 2006 V?
Machined - 2006 V is rated/received certificates of: USA:R
What kind of instrument is Keyway Broach?
A keyway broach is consider a cleaning tool to help remove certain material from whatever object you are cleaning. Broaching is the term used for the use of this tool.
Door locks freezing 1995 Honda CRV?
When the weather warms up or you can park it inside in above freezing conditions - using the narrow spray tube, spray WD-40 into the keyway to displace the water which may have collectred (and is freezing) on the internal lock mechanism. You can follow up by putting powdered graphite (can be found in the key areas of most hardware stores/Home Depot/Lowes key making machines) into the keyway openings.
