What would you like to do?
Answer lcd tv with hdtv
Furniture pads and properly secure the TV in the truck by using the tie down rails. If you're just moving it from one side of the room to another, furniture moving pad…s are probably the best.
Do NOT move a DLP on its back or front. The screen will sag and cause permanent waves in the screen surface. I moved a 61" RCA DLP on its back and have a few waves in …the screen which reflect glare from any light in the viewing area.
Wouldn't recommend it. It's always better to keep them upright unless they're in their original shipping carton. Even then, it's a questionable practice.
One of two things. A reflected image causing `ghosting' in the signal, or your convergence amplifiers have gone bad. (If it's an older three-tube projection set,… that's quite common.)
Very carefully, and don't rush it! If possible, remove external attached speakers, or any other items which may make the TV lighter. If possible, attach padding to the… corners of the TV, in case you bump into walls. Isn't this obvious ?!
This will depend on your specific brand and model. Most models will allow you to pull up the convergene menu by using the original remote. Once is displayed on the screen you …can try to fix it. Note: I you are not able to move one or more colors in any direction your convergece chips have failed . If the convergence is slightly off try running the manual convergence instead of using magic foucus. 1) Turn the TV on 2) Press Magic Focus to begin magic focus 3) Press magic focus again during the magic focus process to get the "stop" screen 4) While stop screen is up, press STATUS or INFO on the remote control (R/C) to bring you to DCAM mode and the service grid 5) When you first get in here? I believe red is the selected color by default (it is flashing). 6) To choose other colors to converge, use the following buttons on the R/C: a) "STATUS" - Green b) "0" - Red c) "ANT" - Blue 7) Start from the center of the screen and work your way out on one color at a time. I adjusted red across the whole screen to match green. Then I switched to blue, and adjusted that to green as well. After you adjust blue, you may want to go back and adjust some red again? etc. until the convergence looks good. (a) Use 4, 6, 2, and 5 on the R/C to move the cursor position(dotted lines). (b) Use thumb stick to move the convergence point color.
I have found Mittsubishi Come Apart From the Front, Remove Speaker cover pulling out to you, then remove the screws under channel,volume switches accros lower facia, Remove th…e center board between speakers, lift screen up toward your ceiling NOTE: there are 2 side pins on the TV wood Case, and 3 Flex Lock Grab Anchors across the top top of the PlexiGlass Frame, Plexi Glass Will BREAK if you bend or drop hammer on" YOU R SCREWED" ....use a Glass Clean Like you do on the Bath Room Mirror and then spary on nice soft towel and clean the Lens, I remove the rear dust panel and blow out all the dust first before cleaning any mirrors,lens....with a shop vac use a new Pain brush and wipe down the Circut boards and Fuses and TV Case ect....Moisture loves dust and electricity loves to ground though moisture so take your time and the paint brush will help move the dust up of the Circutry....after you are done take and blow off your mirror and lens last then wipe lens before your button her up, magnovx Phillips ect come apart from the rear and the mirror come out of some....Have Fun Keep Smiling Merry Christ-mas ...Happy Birthday JESUS" ....Our Wonderful Lord and Savior
Some rear projection sets over fifteen years old are still going strong. Too may factors come into play and it's really hard to say anything for sure about a TV's expected lif…e.
1947, although practical units with pictures bright enough to be seen during the day appeared in the mid 1970's.
Red, green and blue light sources like a digital front projector make up the image and each path of light bounces off a mirror. After they bounce off the mirror, they hit a sc…reen that shows the light in fine vertical lines. Since the light travels roughly 4.5 feet before hitting the screen, the screen can be big but is slightly fuzzy. The mask gives the TV a bad viewing angle. They were the first kind of TV to go above 40 inches in diagonal size and under 18 inches in length/depth. The projector is under the screen, so they are big, and often times have big speaker systems embedded inside. All that means rear projection TVs are made for greater viewing distances.
PT51642V is the model of your Panasonic remote control, not your TV. If you Improve your question to note the model of TV you have, we can help.
A rear projector tv is useful for a better quality of the image, a bigger group of people watching TV in a bigger room. Also is very interesting to create a cinema effect in y…our own house.
amazon.com sells almost everything, including rear projection tvs. They do not have a very large selection and it would probably be in your best interest to go into a smaller …store with support staff more readily available to ask questions.
Rear-projection technology allows for large displays; rear-projection televisions range from 42" to 80" on the diagonal. Furthermore, rear-projection televisions are comparabl…y less expensive than similarly sized plasma televisions. The rear-projection television is also very simple to set up, as no drywall work is required.
Samsung's 63-inch PN63B550 was the largest rear-projection Tv on the market.