0
What is the rear shock absorber bolt size for a 2000 silverado?
Wiki User
∙ 11y ago
The rear shocks take a 21mm wrench...
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
How do you change shock absorbers in 2002 dodge caravan?
# Raise vehicle. # Support the rear axle of the vehicle using 2 jackstands positioned at the outer ends of the axle. NOTE:If the shock absorber lower mounting bolt deflects upward during removal, raise axle by adjusting the support jack. If the lower shock absorber bolt deflects downward during removal, lower the axle by adjusting the support jack. # Remove the shock absorber lower mounting bolt. # While holding shock absorber, remove the shock absorber upper mounting bolt and shock absorber. # While holding shock absorber in position against the frame rail, install the shock absorber upper mounting bolt. # Install the shock absorber lower mounting bolt securing the lower end of the shock absorber to the axle. # Remove the support jack. # Lower the vehicle to the ground so the full curb weight of the vehicle is supported by the suspension. # Tighten the upper and lower shock absorber mounting bolt to a torque of 88 N·m (65 ft. lbs.).
How do you replace rear shock on Volvo s60 2.5T?
I wish someone answered this, I can't seem to be able to take off the top rear shock absorber bolt without it spinning with the top of the schock.
How do you replace the rear shocks on a Ford Windstar?
To remove rear shocks:# Raise and support the vehicle and remove the wheels# Put a jack under the rear axle and raise it slightly to take the tension off the shock# Remove the lower shock absorber bolt/nut and disconnect the shock from the rear axle.# Remove the upper shock absorber-to-chassis bolt to release the shock from the vehicleTo install rear shocks: # Attach the shock absorber to the upper mounting bracket and install a new retaining bolt/nut.# Using the jack you put under the axle, slowly raise the axle while guiding the shock into the lower mounting bracket.# Install a new retaining bolt/nut and tighten to 50-68 ft. lbs.Don't forget to put the wheels back on...----Your Windstar may not have shocks. Please verify. My Windstar has a X look in the back with coil springs and thus no shocks because that is handled by the X.
Will oem wheels from a 2005 silverado fit a 2000?
The stock wheels from a 2005 Silverado is interchangeable with a 2000 Silverado. Bolt patterns should be measured before attempting any wheel changing between models or years.
Will the seats from a 2001-2004 Silverado 2500 Extended cab fit a 2000 Silverado 2500 extended cab?
YES they will bolt right in.
How do you replace a front suspension spring on Renault espace as it appears that the top of the shock etc is under the dash?
There is a cover secured by 4 bolts located at the top of the shock absorber directly under the windscreen wiper arm. Remove that then you can access the 3 nuts that secure the shock absorber top plate at the top of the shock absorber. Support the shock absorber while undoing the 3 nuts after undoing all the lower bolts ( at the caliper / disc end). You may have to disconnect one side of the disc to allow it to swing for access. Use the proper spring compressor tools (spring under extreme compression!) to compress spring to allow for removal of top 3 bolt plate so to change spring after removing shock absorber from vehicle. Assistance probably required to help locate the top plate / 3 nuts on refitting.
Where is located the belt tensioner on mercede E300?
It is right on the front of the engine. Its a vertically mounted shock absorber, held in place on a cam by a 13mm bolt. One of the easiest to get and and undo.
How do you change struts and shocks on 2001 dodge stratus?
AnswerSHOCK ASSEMBLY (FRONT)NOTE: Before proceeding, review SERVICE WARNINGS AND CAUTIONS in this section.REMOVALLoosen wheel nuts.Raise vehicle on jack stands or centered on a frame contact type hoist. See Hoisting in the Lubrication and Maintenance section of this manual, for the required lifting procedure to be used for this vehicle.Remove wheel and tire assembly from location on front of vehicle requiring strut removal.If both shock absorbers are removed, mark the shock absorbers right and left according to which side of the vehicle they were removed from.Remove the wheel speed sensor cable routing bracket Wheel Speed Sensor Cable Routing Bracket from the steering knuckle.Remove the cotter pin and castle nut Ball Joint Attachment To Steering Knuckle from the upper ball joint stud.Remove the upper ball joint stud from the steering knuckle using Puller, Special Tool, C-3894-A Ball Joint Stud Removal From Steering Knuckle Pull steering knuckle outward and position toward the rear of the front wheel opening.Remove pinch bolt attaching shock absorber clevis to shock absorber Shock Absorber Clevis Bracket Pinch BoltRemove the thru-bolt Clevis To Lower Control Arm Attaching Bolt attaching the shock absorber clevis to the lower control arm.Remove the clevis from the shock absorber by carefully tapping the clevis off the shock absorber using a soft (brass) drift.Remove the 4 bolts attaching the shock absorber/upper control arm mounting bracket to the shock tower of the vehicle Shock Assembly Attachment To Shock TowerRemove the shock assembly from the vehicle. The shock assembly is removed out through the front area of the front wheel well.For disassembly and assembly of the shock assembly, refer to DISASSEMBLY AND ASSEMBLY in this section of this group.INSTALLATIONInstall the shock assembly, with the clevis removed, into shock tower. Aligning the 2 locating pins and the 4 mounting holes on the upper control arm shock absorber mount with the 4 holes in shock tower. Install the 4 upper control arm mount to shock tower mounting bolts Shock Assembly Attachment To Shock Tower Tighten the 4 bolts to a torque of 90 N·m (68 ft. lbs.)Install the clevis bracket on the shock absorber. Clevis is installed by tapping it onto the fluid reservoir of the shock absorber using a soft (brass) drift until fully seated against locating tab on shock absorber Clevis Correctly Installed On Shock Absorber The orientation tab on the shock absorber locating tab must be positioned in the split of the clevis.Install the clevis to shock absorber pinch bolt. Do not tighten or torque the bolt at this time.Install the clevis bracket to lower control arm thru-bolt Clevis To Lower Control Arm Attaching Bolt Do not tighten or torque the thru-bolt at this time.Tighten the clevis to shock absorber pinch bolt to a torque of 70 N·m (52 ft. lbs.)Install upper ball joint into steering knuckle. Install castle nut on ball joint stud. Tighten castle nut to a torque of 62 N·m (45 ft. lbs.) Install cotter pin in stud of ball joint Ball Joint Attachment To Steering KnuckleInstall the routing bracket for the speed control cable Wheel Speed Sensor Cable Routing Bracket on the steering knuckle. Install and securely tighten the routing bracket attaching bolt Wheel Speed Sensor Cable Routing BracketCAUTION: When supporting lower control arm with jack stand, do not position jack stand under the ball joint cap on the lower control arm. Position in area of lower control arm shown in Lower Control Arm Correctly Supported By Jack StandLower vehicle to the ground with a jack stand positioned under the lower control arm Lower Control Arm Correctly Supported By Jack Stand Continue to lower vehicle so the total weight of the vehicle is supported by the jack stand and lower control arm.Tighten the shock absorber clevis to lower control arm bushing thru-bolt to a torque of 90 N·m (68 ft. lbs.)Raise the vehicle, then remove the jack stand.Install the tire and wheel assembly. Tighten the wheel mounting stud nuts in proper sequence until all nuts are torqued to half specification. Then repeat the tightening sequence to the full specified torque of 135 N·m (100 ft. lbs.)Lower the vehicle.
How do you find engine number on scooter Yamaha vino 50 cc?
The engine number on all Vino scooters is on the rider's left of the machine near where the rear shock absorber is bolted to the engine. The number is stamped on the flat upper surface of the crankcase between the oil plug and shock absorber bolt. You don't need to remove body panels.
What is the bolt patter for a 1994 Chevy Silverado?
what is the bolt pattern for a 1987 Chevy silverado
Can you replace a front bumper on a 2001 Chevy silverado 2500 hd extended cab 4-wheel drive with a 2000 Chevy silverado?
Yes it will bolt right up.
Will a 1998 silverado interior bolt up in a 1993 silverado?
no
