0
What voltage should read at the outputs of a hundred amp breaker?
Wiki User
∙ 14y ago
It depends on where the breaker is fitted. Is it installed in a panel in the US, Canada or Another Country which also uses the 60Hz, 120 Volts standard supply service?
Or is it fitted in Europe or elsewhere using the 50Hz, 230 Volts standard?
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
The amperage of the breaker dont determine the voltage reading. If your panel is 120v every breaker regarding of amperage rating or size will still read 120v. but to answer your question as it reads... the voltage on the output should read the same voltage as the input or line side.. that is if the breaker is in the on position.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Why am I only getting 120 volts from a 30 amp breaker that should be feeding 220 volts?
I assume you have a 30 amp two pole 220 volts breaker. Check the voltage source. If the source voltage is 220V, but out let voltage is 120 then the breaker must be faulty, a high resistance or partial open circuit could have caused the reduced voltage at the breaker outlet.
How many watts can be put on a 20 amp 208 volt circuit breaker?
20-amp breakers can be found for many different voltage levels. The higher-voltage ones tend to be more expensive. A breaker can be used in a circuit of equal or lower voltage than the rated voltage of the breaker.
What size amp circuit breaker should be used for a Rheem RALB36JAZ?
You need to look on the manufacturer's specification plate on the unit for the amperage and voltage.
What size wire and breaker do you need to run a 9000max watt generator?
If it is a portable generator the breaker should be self contained within the generators panel. If the generator is a stationary standby unit a voltage has to be stated to calculate the conductor size and hence the breaker size to protect the conductor. Amps = Watts/Volts.
What size breaker do i need for a central heat and air unit?
The breaker type be it a single pole or double pole will depend on what voltage the air conditioner operates on. Once the voltage is established, the sizing of the breaker depends on what the current draw of the air conditioner is.
Why would power be received before breaker but with breaker on no power is in any recepticles?
The voltage before the breaker is from the distribution panel's buss bars. This voltage is controlled by the panel's main breaker. To have no voltage on the terminal of the breaker means that either the breaker is shut off or it has gone into a trip position. If it has tripped push the handle of the breaker to the off position and then to the on position. This should reset the breaker. If the voltage is not present at the output terminal of the breaker after resetting it, then replace the breaker as it has a fault in it.
Why am I only getting 120 volts from a 30 amp breaker that should be feeding 220 volts?
I assume you have a 30 amp two pole 220 volts breaker. Check the voltage source. If the source voltage is 220V, but out let voltage is 120 then the breaker must be faulty, a high resistance or partial open circuit could have caused the reduced voltage at the breaker outlet.
How much voltage should be in 2pole circuit breaker?
In America, a 2-pole breaker is controlling 240V. 120V per leg.
How do you test a 220 volt breaker?
You will need a multimeter to check a 220 volt breaker. You should unplug appliances that go to that particular breaker. Use the multimeter at the breaker to check the voltage. If it shows 220, then the breaker is okay. If it doesn't, then the breaker is no good.
Where is the circuit breaker for a hot water heater?
The best way to determine which circuit breaker is for the water heater is with a voltage meter, It is suppose to be only one circuit breaker, but in a faulty application it could be two breakers
How many watts can be put on a 20 amp 208 volt circuit breaker?
20-amp breakers can be found for many different voltage levels. The higher-voltage ones tend to be more expensive. A breaker can be used in a circuit of equal or lower voltage than the rated voltage of the breaker.
You lost a voltage leg by connecting the ground wire to the circuit breaker but com ed wires are still energized?
Yes this could be true. The breaker to the load will have tripped. The main breaker should still be allowing voltage to the distribution panel because it did not trip. If the main breaker tripped then the distribution panel must have been close to maximum amperage and the shorting of the branch circuit was enough to trip the mains.
When a voltage leg is lost by connecting the ground wire to the circuit breaker are com ed wires still energized?
Yes this could be true. The breaker to the load will have tripped. The main breaker should still be allowing voltage to the distribution panel because it did not trip. If the main breaker tripped then the distribution panel must have been close to maximum amperage and the shorting of the branch circuit was enough to trip the mains.
What size amp circuit breaker should be used for a Rheem RALB36JAZ?
You need to look on the manufacturer's specification plate on the unit for the amperage and voltage.
What happens to voltage during a short to ground?
Basically, the same as if you had a short to neutral, since the neutral and ground are tied to the same bus bar in the breaker panel. The breaker should trip, or the fuse should blow. Supply of voltage then stops.See the answer to the Related Question about GFCIs - shown below - for information about circuit protection when even a small current flows to ground.
What circuit breaker rating is commonly used for a radial circuit?
In the terms of voltage it should be in kV but when we are using the current term than it should be in kiloamperes or kA because the short circuit current level of the circuit breaker is very high.AnswerIt depends entirely on the voltage level and load currents you are talking about. It will be completely different for, say, a 132-kV system than for, say, a 230 V system. So, does your question apply to high-voltage systems or low-voltage systems?
What is wrong with your 240 outlet if it is only outputting 120v and breakers are just fine?
A breaker will not step-down power/ voltage. Its most likely a problem from your suppliers. More likely you aren't measuring the voltage correctly. There is 120 V between neutral and either Hot wire. There should be 240 between the two hot wires. If this is what you are measuring and you are sure the breaker is 240 volts you should be able to measure 240 at the output of the breaker. If it isn't there your panel has a problem.
