0
When removing screws while working on a laptop what should be done with the screws?
Wiki User
∙ 7y ago
- Put screws (and other parts) in a safe tray or container so they won't roll away, blow away, get lost.
- Keep track of which size screw came from which screw hole so you don't put it into the wrong size hole leaving a loose screw or a stripped plastic screw hole.
- It may even be a good idea to keep track of where each screw came from as some screws are very close in size.
Wiki User
∙ 7y ago
Add your answer:
Earn +20 pts
How to install radio in Jeep Liberty 2005?
i have a 2007 liberty sport4X4 (it should be the same. you might have an ash tray in which you have to pull out first.) and there is a compartment down beside the lighter and in the back of that hole there is one Phillips screw that you need to remove. After removing the screww you can just grab the whole plastic piece and it should snap out, it also contains the A/C components and it just popped off. Then there are (4) Phillips screws holding the radio in the dash. That's it. One of the simplest dashes to take the radio out of. this is for a different installation but it has pictures of the dashhttp://logjam.d3datasolutions.com/forums/index.php?showtopic=43 I have a 2005 liberty. It's super easy. My FM just stopped working. It's strange. My CD player works, and my AM works. But FM doesn't play? It shows the song, the station... time. etc. But it just stopped working? DUMB!!! Anyways, one screw down by the lighter.. Then the whole front panel pops off. Then 4 screws around the radio. Phillips screws.. Then it comes right out. It's nice and easy.
Is there a way you can use your laptop as good quality guitar processor?
A laptop should (depending on the sound card, and ram) be just fine for making music. However, you might not hear the best sound, as laptop speakers tend to lack bass power.
How to remove fender flares on a 2000 jeep Sahara?
There should be some screws and nuts and bolts.
How do you secure a fender guitar pickup?
make sure all the screws are on the faceplate right and it should be
Changing Shift Knob face in 90 Cherokee Sport?
The shift knob should be held on by set screws if its a manual or threaded on if its an auto, in the case of an auto you would have to disconnect the shift button to change the handle. The shift knob should be held on by set screws if its a manual or threaded on if its an auto, in the case of an auto you would have to disconnect the shift button to change the handle. The shift knob should be held on by set screws if its a manual or threaded on if its an auto, in the case of an auto you would have to disconnect the shift button to change the handle.
How do you remove sun visor Toyota RAV4?
You can remove the sun visor on your Toyota Rav4 by removing the screws on the swivel arm. When they screws are remove the visor should come off.
What should be removed before working on laptop circuits?
One reason that the manufacturers have factory warrenty is to have some say in how well and reliable the laptop is when it leaves the factory. If you work ion the laptop circuits you risk wreaking the laptop not just wreaking any warrenty. Qualified, trained, experienced people should work on laptop circuits.
How do you remove the Deck from a 1989 Caprice Wagon?
there are two screws on top of the ac control panel that is located on top of the stereo and two other screws are under the radio but to get to this screws u need to remove the ash trey and then after removing those 4 screws the radio should pop right off
How do you change the door speakers in a 1995 Ford Explorer?
Remove the screws under the door handle on the door panel, and take off the trim plate. Then remove the door lock knob by untwisting it. Pull the door panel with a putty knife or door panel puller, removing any screws and disconnecting the wiring. Take speaker out by removing screws that should now be visible.
When removing the cover what should you take care to remove only the screws that hold the cover on?
the answer to your problem is first take care of that and enroll in coe115-1l
Should i sell my broken not working macbook for an working 4th gen iPod?
Yes u should that a good deal getting an £80 ish ipod with an £70-£80 broken laptop
How often should you replace your laptop battery?
If your laptop battery fails or no longer holds a sufficient charge, you can easily replace it. But as long as it is working fine then you don't need to replace it.
Which power mode should be used by a laptop so that all the data is saved all the applications the user was working on are left open and there is no power used by the laptop?
Hibernate - is the correct answerhibernate is safe mode for laptop then shutting it down
How to Dismantle a video cassette One of the leaders has become disconnected from the spool. I have removed the screws but there is still one connection in the centre?
After removing the screws and the label on the edge, the cassette halves should separate.There is a screw in the centre, recessed in a deep pocket.
Disassemble a gateway 7330?
Removing the Gateway 7330 keyboard to get to the heatsink. Remove the battery for safety's sake. There is a panel with the on/off switch etc, next to the display. It does not look like it comes off, but it does. The first step is to remove 2 long screws from the bottom of the laptop. These are near the back edge, and are slightly staggered from each other. They are the middle two screws. After removing them, look at the back edge of the computer where the screen "hinges or pivots are. There are two silver plastic pieces. With the display approx vertical (in normal viewing position), carefully press in on the bottom of the two pieces and pry them up until the locking tab is exposed and sitting outside of the plastic. From the front of the laptop, pry these silver plastic pieces up (you may have to tilt the display backward). The plastic strip WILL come out, (it rocks upward toward the front edge of the laptop. Once it is up, there are two screws, one at each end of the keyboard, that secure it. Remove these screws and the keyboard lifts up, to expose a large sheet of metal. There are two long screws and some short ones. Removing this, will allow the metal to be removed from the heatsink/fan assembly. Removing the 4 large slotted screws, and lifting the glued down flap of plastic (to free the cable going to the display), should allow you to manipulate the fans and heatsinks out of the laptop. In my case, it pulled the processor with it, and I had to carefully pry it off the heatsink and re-insert it into the socket. I then replaced the silver grease. HOWEVER: to clean out the fans, you can used compressed air and blow down through the fans, and into the vents from the outside. Leave the fans in place, with the heatsink screwed down, and you can put the battery back in, and power the laptop up. Observe the fans and if they are not running, they can be removed and replaced. (one comes out from the top of the heatsink, one comes out from the bottom of the heat sink.)
Who should get a laptop and who should not in office?
the boss should get a laptop and the cleaner shouldn't.
How to connect a portable printer to laptop?
You should consult the manual that came with your portable printer. In said manual there should be a troubleshooting guide for how to asses why the printer is not working and how to fix it.
