0
you need to turn the caliper piston clockwise as it is being pushed in. There is a special tool but you can work it in with a c clamp, just make sure you don't tear the rubber boot. Also, make sure the nepressin area of the head of the caliper aligns with the raised point on the inner pad
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Saab 93 2006 how to retract rear brake caliper?
us Cclamp to retract caliper leave old brake pad in place put clamp over caliper with 1 end on brake pad and the other over caliper back start to tighten very simple.
How do you get rear caliper pistons to retract on citroen xsara piccasso?
Caliper pistons should retract if calipers are in working order. Calipers need to be removed and rebuilt or replaced. A brake fluid flush is highly recommended.
Change rear brake pads on Audi a6 2005?
a special scanner called a v.a.g. has to be used to retract the electronic e brake system, and will also retract caliper piston..DO NOT TRY WITH OUT TOOL !!!!!
How do you get a piston in rear brake caliper to retract back into the caliper on a 2000 Mazda 626?
On the back of the caliper there should be a bolt its a 14mm you take it out and inside there is a bolt also its Allen key you use and Allen key and retract the caliper. it works on all 626 from 1994 till 2002
How do the brake caliper go back on a 1985 linclon mark 6 do you us a tool what tools?
The front brake caliper should retract with minimal effort with the aid of a c-clamp and an old brake pad. If it takes alot of pressure to make it retract I would replace the caliper. The rear brake caliper is a different story because it houses the e-brake also. The brake caliper piston must be rotated clockwise as you apply pressure to retract it. This requires a special tool that you can purchase from your local auto parts store. This tool is not expensive, it should be less than $20.
How do you compress the caliper piston on a 1985 Nissan truck brake assembly?
If it is the front brake use a "C" clamp to retract piston If it is the rear and the parking brake is used by this caliper piston is threaded and a special tool (not expensive) available at Sears or auto parts to "screw" piston into caliper body
How do you retract the rear brake piston on a 2008 town and country?
Compressing the rear brake caliper piston on a 2008 Chrysler Town and Country requires a special tool that pushes in and turns the piston at the same time.
How do you get piston in rear brake caliper to retract back into the caliper so you can change pads on a 2002 Mazda protege 5?
There is a 14 mm bolt on back of caliper. Remove this & use a 4 mm Allen wrench to back piston into caliper.
How do you change the rear brake pads on a 1996 Ford Explorer?
Remove wheels Loosen 2 caliper mounting bolts and remove Remove Rotor (if peel off type) Resecure caliper Remove brake pads Need to get special tool to retract piston into caliper Do not retract using "C" clamp these pistons have to screw back into calpier (Clockwise) After piston retracted totally install new brake pads and reverse procedure to install DO NOT MOVE VEHICLE UNTIL BRAKE IS PUMPED TO RESET PADS TO CALIPER
When replacing rear brake pads on a 99 Olds Intrigue how tight must the bolts be for brake caliper?
Rear caliper to rear caliper bracket bolts, 32 ft. lbs.
Why does the emergency brake handle on a 1993 lebaron convertible 3.0 sometimes pull all the way up without putting on the brake?
Loose or broken cable Rear brakes not adjusted properly Rear rotor out of round-causing caliper to retract on slides
How do you change rear pads and rotors when caliper has pistons?
Depending on the make/model/year of vehicle, you may have to get a rear caliper tool. Some rear calipers need to be turned to retract them.
