Yes, they will. One can connect anything to anything else. Will it work? If so, how well? Is it safe? If the four speakers are connected in series, the total impedance of the speakers will be the sum of all the impedances of the speakers: 5.5 + 5.5 + 5.5 + 5.5 = 22 ohms The 22 ohm load on the amplifier will be a bit higher than the amp has been designed for, but the setup will work. At modest power levels it is doubtful that anything audible will be noticeable because of that slight mismatch, and as long as one doesn't crank it up too high, the amp won't notice the difference. It would be wise when hooking up the speakers to insure they are all hooked up in phase... Something important has to be added: There is really no 16 ohm amplifier on the market. The amplifier will have an output impedance of around 0.08 ohms. In hi-fi we have always impedance bridging. Zout << Zin. That means that the output impedance of the amplifier is much less than the input impedance of the loud speaker. The damping factor Df = Zin / Zout tells you what Zout is. Zout = Zin/Df. If the damping factor Df = 200 and the loudspeaker impedance is Zin = 16 ohms, the output impedance of the amplifier is Zout = 16 / 200 = 0.08 ohms. You see, there is no "16 ohm amplifier" with a 16 ohm output impedance. Scroll down to related links and look at "Voltage Bridging - Zout < Zin".
no. input impedance is low & output impedance is high
No Problem to do this, but there are really no amplifiers with an output impedance of 16 ohms on the market. All loudspeaker amplifiers have an impedance of less than 0.5 ohm. Scroll down to related links and look at "Impedance bridging - Wikipedia".
Yes, you can use 2 in series, IE daisy chain them to add up to 8 ohms.For stereo you would need 4 speakers not 2. mono, 2 not one.Most Amplifiers work OK driving to a lower impedance loads anyway so just hook them up. Very high power levels may overheat the amp but at normal volume it should be fine. Something important is added: There are no 8 ohm amplifiers! The amplifier will have an output impedance of around 0.04 ohms. In hi-fi we have always impedance bridging. Zout
Most power amplifiers will handle a load of 6 ohms. The spec you need to look at is the power handling of the speakers. If they are rated for 100 watts program power, then look for an amplifier rated for 100 watts RMS output. Any amplifier can be connected with adapter cables to the typical 1/8" output of your computer.
Yes you can. 2 ohms is as low as you can go with that amp MOST car subs have 4 ohm voice coils. The bigger the number, the less low bass frequency run two single voice coils subs and you'll be fine. It's a myth. There is really no 2 Ohm amplifier on the market. And there never was. The amplifier will have an output impedance of around 0.04 ohms. In hi-fi we have always impedance bridging. Zout << Zin. That means the output impedance of the amplifier is much less than the input impedance of the loud speaker. The damping factor Df = Zin / Zout tells you what Zout is. Zout = Zin/Df. If the damping factor Df = 200 and the loudspeaker impedance is Zin = 4 ohms, the output impedance of the amplifier is Zout = 4 / 200 = 0.02 ohms. You see, there is no "2 ohm amplifier" on the market with a 2 ohm output impedance. Scroll down to related links and look at "Voltage Bridging or impedance bridging - Zout < Zin".
Sorry, but there is really no amplifier on the market with 8 ohms output impedance. The output impedance of a power amplifier is always less than 0.5 ohms. We use no impedance matching. We use voltage bridging. Scroll down to related links and look at "Interconnection of two audio units - Power amplifier and passive loudspeaker".
There is really no amplifier on the market which has an output impedance of 4 ohms. The impedance of an amplifier is always less than 0.5 ohms. We do not use matching, we use bridging when we connect the amplifier to the loudspeaker. Scroll down to related links and look at "Interconnection of two audio units".
If the TV has an audio output, connect this to a stereo amplifier, and then connect speakers to this. Modern TV's don't have amplifiers for external speakers.
First, you must know: There is no 4 ohm amplifier. All audio amplifiers have an output impedance of smaller than 0.5 ohms. So you use impedance bridging. No problem to connect the 0.5 ohm output to your 4 ohm loudspeaker. Scroll down to related links and look at "Impedance bridging - Wikipedia".
no. input impedance is low & output impedance is high
It's a myth. There is really no 6 Ohm amplifier on the market. And there never was. The amplifier will have an output impedance of around 0.04 ohms. In hi-fi we have always impedance bridging. Zout
The TV will need to have AUDIO OUTPUT jacks to connect to the speakers or a amplifier to power the speakers and subwoofer.
In general, you cannot connect a pair of speakers to a computer, because the computer's sound board does not normally include a power amplifier fit to drive a speaker.It might be possible to drive very small speakers with a high impedance directly from a sound board's headphone output, though.Note that most "PC Speakers" can be directly connected to a computer's audio output because the speaker itself contains a power amplifier. Strictly speaking, such a speaker is a combination of a loudspeaker and an amplifier (sometimes also called an active speaker).
There are no 4 ohm amplifiers!The amplifier will have an output impedance of around 0.04 ohms. In hi-fi we have always impedance bridging. Zout
It's a myth. There is really no 8 Ohm amplifier on the market. And there never was. The amplifier will have an output impedance of around 0.04 ohms. In hi-fi we have always impedance bridging. Zout
Yes. And it will also present the wrong load impedance (mismatch) at the output of the audio amplifier, with the possibility of damage to the amplifier.
All amplifiers are rated to handle a certain speaker impedance. The majority of loudspeakers have an impedance of 8 ohms while most amplifiers will be able to drive a minimum load of 4 ohms. It is important to check the ratings of the amplifier before adding more speakers. If two 8 ohm speakers are wired in parallel, the total impedance will be 4 ohms. If 3 speakers are wired in parallel then the total impedance will reduce to around 2.5 ohms. If the total speaker impedance is lower than the rated impedance of the amplifier, it is quite possible to damage the amplifier as the output level is increased. To be safe, make sure you understand the impedances of the speakers and the amplifier's rating before hooking anything up.