answersLogoWhite

0


Best Answer

Do not belive so. Most flywheels that have to be in a certain place will only bolt on that way. The bolt holes will be offset just enough that it will only bolt on in one place.

User Avatar

Wiki User

โˆ™ 2007-05-21 23:18:55
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: 1991 Chevrolet sprint 1.0 liter-does the flywheel have to be bolted on in a certain position to balance properly Manual transmission?
Write your answer...
Submit
Related questions

How do you change crankshaft position sensor on 04' aerio?

remove the engine and transmission from the car, then remove engine flywheel and it will be right there


Where is the crank position sensor on a 1999 Nissan Frontier located?

For the manual transmission is located on the upper left (driver) side of the transmission where the transmission bolts to the engine. It reads the flywheel. The mounting screw also holds down a metal cover for the sensor. I was able to reach it from under the car when the transmission was lowered.


Where is the crank sensor located?

AnswerThe position will vary according to the year, make and model. However, crank sensors are usually located in the transmission bell housing, just above the flywheel.


What is the tapping noise when 2002 regal is put into drive?

the doors are being placed in locked position If it's coming from the engine or transmission area, I would suspect a cracked flywheel or flexplate.


Where is the crank position sensor located on a 1997 susuki sidekick?

ON the SOHC models the Crankshaft position sensor is located on the front of the oil pan, The DOHC is located behind the engine, the transmission and the flywheel must be removed to the sensor on the DOHC models


What is the sensor that is on top of the transmission towards the front of the bell-housing that goes through just above the flywheel on a 1995 Nissan 240SX 5-speed?

its the crankshaft position sensor


Hi you are trying to change transmission in your 2000 2.4 cirrus but you can only get 2 of the bolts to fit into the flywheel the other 2 wont line up do you got to loosen the tranny?

try rotating the flywheel as the holes will only line up in a certain position on some vehicles. I hope this solves your problem


Where would you find the crankshaft position sensor for a Chevrolet 2000 tracker?

on the driver side top be hind valve cover 5/30/12 - The 2000 Chevy Tracker may have one of 2 engines - 1.6 or 2.0 liter. The 1.6 version has an easily accessible crankshaft position sensor at the rear of the cylinder head on the driver's side. But the 2.0 engine requires the transmission & flywheel to be removed. That's a big difference in effort & cost.


After installing transmission in 1991 ltd crown vic car will no longer start is there a certain position the torque converter and flywheel should be in before the car will start again Ran fine before?

sounds like a ele. problem


Where is the vehicle speed sensor on a Chevy Lumina APV minivan?

The Chevrolet Lumina speed sensor can be found on the back of the transmission. The exact position of the speed sensor is dependent upon the year of the automobile.


Where is the throttle position sensor in a 2005 Chevrolet Cobalt?

The throttle position sensor is in the throttle body.


Crank position location on 03 jeep grand Cherokee?

Runs off the flywheel passenger rear of engine area Runs off the flywheel passenger rear of engine area


Function of flywheel in reciprocating engine?

The flywheel smooths out the pulse of the power stroke and its inertia allows the crank shaft to continue rotating to bring the next piston into position to fire. Look at it like this: You could pedal your bicycle with one foot if the pedal had a flywheel on it.


Where is the crank position sensor on a 2000 elantra?

The (CKP) crankshaft position sensor is located on the front side of the engine block,near the flywheel/driveplate.


Where is the crankshaft position sensor on a 98 Hyundai elantra?

The crankshaft position sensor is located on the front side of the engine block near the flywheel/driveplate


Where is the crank position sensor on a 1999 Chevrolet Malibu?

The 1999 Chevrolet Alamo crank shaft position sensor is located on the back of the engine. You will need to remove the rear engine cover in order to access the crank position sensor.


Where is the throttle position sensor on a 2003 Chevrolet suburban?

The throttle position sensor on a 2003 Chevrolet Suburban is located on the side of the throttle body. It notifies the vehicle's computer of the actual position of the throttle plate in relation to the throttle body.


Where is the camshaft position sensor located on a 1997 Chevrolet K 3500?

The 1997 Chevrolet K 3500 pickup truck camshaft position sensor is located on the back of the cylinder head. The camshaft position sensor should be labeled as such.


How do you adjust the throttle position sensor on a Chevrolet Camaro?

It is not adjustable.


Where is the crank position sensor on the 2006 Chevrolet trailblazer?

7 oclock position behind the crankshaft pulley


Where is the crankshaft position sensor on a 1987 Chevrolet celebrity?

The crankshaft position sensor on a 1987 Chevrolet Celebrity is on the side of the engine nearest the firewall. I need to know which engine to give a more specific answer.


Where is the flex plate for crankshaft sensor located on 97 dodge truck 5.2?

The flex plate is the flywheel. It is between the crankshaft and torque converter. The crankshaft position sensor is located behind the passenger side cylinder head, through the top of the transmission case.


Where is the throttle position sensor located on a 1998 Chevrolet Camaro?

The throttle position sensor is located on the throttle plate.


Where is the engine serial number located on a 2006 Chevy Malibu?

The 17 number VIN is ;located on the passenger side front lower windscreen The Chevrolet Malibu world manufacturer identifier is position 1-2-3-.In position 4-5 of the Chevrolet Malibu model number and in position 8 is the Chevrolet Malibu engine number.


After installing transmission in 1991 ltd crown vic car will no longer start Is a certain position the torque converter and flywheel should be in before the car will start again Ran fine before?

make sure the park/neutral switch is connected and adjusted properly