0
2002 Chevy Monte Carlo change engine oil light wont reset I have tried the method suggested which was turn key on pat the accelerator 3 times within 5 seconds then turn key off then start engine?
Stog1493
turn key on pump accelerator 3 times hold on 3rd time till light changes
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you reset the change engine oil light on your 2000 Silverado?
Turn the ignition key to the run position and pump the accelerator 3 times within 5 seconds.
How do you reset oil change light on vauxhall antara 2.0cdi?
If the oil change light on your Vauxhall Antara 2.0CDTI doesn't reset after changing the oil, you can reset it manually. Make sure all doors on the vehicle are closed, fully press the accelerator to the floor, and switch on the engine. Press the accelerator down three times in five seconds, and turn off the engine.
How do you reset the change oil light for a 03 grand prix?
Try turning key to "on" position without starting engine Depress Accelerator 5 times to floor within 10 seconds
How do you reset the change oil light for a 2000 Chevrolet impala?
Turn ignition to on without starting engine and press all the way down on the accelerator 3 times within 5 seconds
How do you reset the oil change light in a 2002 gmc sierra with a duramax engine?
turn the ignition on but do not start, press accelerator all the way to floor three times within five seconds.
How do you do a throttle body relearn on a 2005 sentra?
Warm up engine. - Put in neutral (n)! -Make sure everything is off (RADIO, AC, ETC.) -Turn ignition switch ?OFF? and wait at least 10 seconds. -Confirm that accelerator pedal is fully released, turn ignition switch ?ON? and wait 3 seconds. -Repeat the following procedure quickly five times within 5 seconds. a. Fully depress the accelerator pedal. b. Fully release the accelerator pedal. -Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the MIL stops blinking and turned ON. -Fully release the accelerator pedal within 3 seconds after the MIL goes ON. -Start engine and let it idle. -Wait 20 seconds.
How to reset Oil change light silver?
Turn the key to "power on" (but don't START the engine!)....press the accelerator pedal 3 times within 5 seconds. The CHANGE OIL light will flash a couple of times and the reset is complete.
How do you reset the Service Engine light after changing oil change in a 96 Blazer LS 4x4?
To reset "CHANGE OIL" light, turn the ignition switch to the run position without starting the engine. Fully depress and release the accelerator pedal 3 times within 5 seconds.
How do you reset the change oil light on a 1991 Eldorado?
To reset "CHANGE OIL" light, turn the ignition switch to the run position without starting the engine. Fully depress and release the accelerator pedal 3 times within 5 seconds
How do you get the Change Engine Oil lamp to go out after you have changed the oil on a 2004 GMC Envoy?
Turn ignition to the "ON" position. Slowly depress accelerator pedal 3 times within 5 seconds. "CHANGE ENGINE OIL" lamp will start to flash. Turn ignition off. Start engine. Light will go out. Also works on 2006 Envoys. I would also suggest to depress the accelerator sharply and not too slowly otherwise it doesn't register.
How do you reset the oil change light for a 1997 cheverlet lumina?
Turn ignition on but do not start engine, depress accelerator to the floor three times within 5 seconds, oil change light should flash 5 times, oil change light is reset if you did this correctly.
How do you reset the oil change information notice after an oil change on a Chrysler Town and Country?
Turn the ignition key to the ON position (don't start the engine) and pump the accelerator three times within 10 seconds. Turn the key to OFF. That will reset the message.
