To reset the service CCR light on a 1991 Eldorado, disconnect the battery for 10 minutes. Reconnect it and start the car.
how do you reset engine light on 1991 volvo 240
You can't. The SRS light is on because the SRS (Supplemental Restraint System) has detected a fault in the system. Until it is fixed the light will remain on and the SRS will not function if needed. Once the necessary repairs are done the SRS system will reset the light itself.
reset the brakelamp light on the dashboard - Honda prelude 1991
How do you reset the check engine light on a 1991 mercedes Benz 560 Sel
What is needed when the ccr is driver information center
Remove steering wheel and signal switch
When "CHANGE OIL SOON" light is illuminated, find the hole in the underside of the dash on the passenger side near the door. Insert a blunt instrument into the hole and press the switch. The light will flash four times when the system is reset.
There is no reset for a check gauges light. If the light is on, there is a problem either with the temperature oil pressure or voltage.
Because you need to reset the light after you change the oil. Changing the oil doesn´t turn off the light automatically , you need to reset it. there is a very small push button on the dash board that has a label "RESET OIL CHANGE", with the engine off, push and keep pushing while you turn the key to power up the accesories but don´t turn the engine on. the light will go off after a second or so. Because you need to reset the light after you change the oil. Changing the oil doesn´t turn off the light automatically , you need to reset it. there is a very small push button on the dash board that has a label "RESET OIL CHANGE", with the engine off, push and keep pushing while you turn the key to power up the accesories but don´t turn the engine on. the light will go off after a second or so.
Have vehicle scanned to determine the problem
The maintenance light on all early model hondas have three stages. Green, orange and then red. This light only serves as a reminder to change your oil, air filter and to do other routine maintenance. If you were to service the vehicle and not reset the light it would just stay on. It changes color by miles. It's green when it is reset and as you drive it will eventually change to orange and then red regardless of any services done to the vehicle. To reset look on the instrument panel for a slot near the light and insert your key this will change it back to green.
you get a pin and push the little hole near the bottom of the right hand side proceed with change the time, date, etc...
Disconnect the battery for about 1 min.
Take the bulb out
Unplug or replace maint. timer
i think you cannot reset, you need to buy a new air bag ecu
Disconnect the negative battery cable from the battery, wait a few minutes then reconnect it. But, if the reason the light came on isn't fixed, the light will only come back on again.
A 1991 Chrysler does not have a reset switch.
1993-1996 Fleetwood1. Turn the ignition key to the RUN position.2. Fully depress and release the accelerator pedal 3 times within 5 seconds.3. The CHANGE OIL light should flash two times and then go out.4. Turn the ignition OFF.If the CHANGE OIL light comes on and stays on for 5 seconds, it did not reset. You'll need to reset the system again. 1991-1993 Deville, & FWD FleetwoodWhen "CHANGE OIL SOON" light is illuminatedPress and hold the "RESET" and "RANGE" buttons on the Fuel Data Center for 5 to 60 seconds. When the buttons are released, the light will flash four times if it has been reset. If the light comes back on for more than 5 seconds, repeat the procedure. [http://myweb.accessus.net/~090/cadireset.html Available At] Good Luck and Remember.Change Your Mind, Not Your Oil.Use the First In Synthetic Motor Oil's.See My Bio For more information.
remove battery cable for 1 min
There is a reset button on the passenger side under the dash. Turn the ignigion on but don't start the car. Press and hold the reset button for about 5-15 seconds. Turn off ignigion and turn back on. It should reset then. If not, push the button with the ignition off and then turn the car on after the 15 seconds.
If a 1991 Chevrolet S10 Blazer warning brake light always stays on, it could just be a malfunction of the light. To reset it, disconnect the battery for 10 minutes.