0
Can I wire nut two black wires together and hook 1 to a breaker?
Wiki User
∙ 7y ago
Not according to the electrical code. It requires each separate circuit to be fed individually from its own breaker. If allowed it would reduce the total capacity of each circuit from one amp per outlet to a half amp per outlet if the circuit was fully loaded.The work around in situations like this is to use a tandem breaker which gives you the capacity of two complete circuits and only using one breaker slot in the distribution panel board.
Wiki User
∙ 7y ago
Wiki User
∙ 7y agoNot advisable as electrical runs should be one piece without splices along the way. Any wire nut connection can come lose over time and/or short out.
Add your answer:
Earn +20 pts
How do you hook up a water heater with red black and white wires?
Sounds like it is a 220-240 Volt hot water heater. The black and red are connected to the 220 volts supply and the white is connected to Neutral. At the breaker panel red and black connect to the 2-pole 220 volt breaker and white goes to the neutral bus bar.
How do you connect wire to a breaker?
There is 220 volts between the two poles. If you are running 2 wires (black and white) + ground then you hook black to one pole and white to the other. Put red or black electric tape on each end of the white wire and wrap around wire for 3 inches or so next to the connection so the next person will be able to see that the wire is hot and not a neutral.
How do you hook up a three phase welder?
Easy as one,two and three. There are four primary wires coming from you service panel.(provided you have three phase service) you can check by looking at the weather head on the roof. if it has three wires you have single phase but if it has four then you have three phase. the hot wires will be black,red and brown. the neutral will be white or green. the welder should have a manual that will give you the lead phase wire(most likely black to black) the other two hot wires can hook to any other hot wire. The neutral goes to the white or green and posts to the panel. If the welder has a switching power supply then you must have a three phase converter.
How do you hook up the distribution panel box with red white black and ground wires?
Without more information that appears to be a 240 volt circuit. Red & black would connect to the 240 volt breaker, white connects to the neutral bar, and ground conductor from the ground rods or ground plate connects to the neutral bar. Make sure that the bonding screw is in the neutral bar and it is screwed through to bond the distribution panel enclosure to the neutral bar.
What kind of breaker would you use for a 220 hook up?
In North America a two pole breaker will be used in the distribution panel for a supply of 240 volts for a 240 volt load.
How do you hook up a water heater with red black and white wires?
Sounds like it is a 220-240 Volt hot water heater. The black and red are connected to the 220 volts supply and the white is connected to Neutral. At the breaker panel red and black connect to the 2-pole 220 volt breaker and white goes to the neutral bus bar.
How do you hook up aftermarket stereo in 1977 Lincoln?
on factory wire harnes, there are 5 speaker wires. 4 are (+). on speakers, but only one (-). when i hook up aftermarket head unit do i hook up all negative speaker wires together
How do you connect wire to a breaker?
There is 220 volts between the two poles. If you are running 2 wires (black and white) + ground then you hook black to one pole and white to the other. Put red or black electric tape on each end of the white wire and wrap around wire for 3 inches or so next to the connection so the next person will be able to see that the wire is hot and not a neutral.
How do you wire duplex receptacle using14-3 wire Also with 14-2 wire The wires are already ran to 15 amp breakers and capped off. i would like to hook them up. Thank You?
Sort of confusing are you using 14-3 just for the receptacle with 14-2 to the breaker or the other way around. Either way doesn't matter since you only need 2 wires and a ground for the outlets. The 14-3 should have Red, Black, White and bare wires. 14-2 should have Black, White and bare. All you need are Black, White and Bare. Forget about the red one. Hook the two outlets together with short jumper wires about 6 inches long. Looking at the outlet with the ground facing down, the bare wire goes on the bottom green terminal. The white wire goes on the left side of the outlet. The black goes on the right side of the outlet. Take the 6 inch jumper wire and go from the left side of one outlet to the left side of the second outlet. White to white, black to black, bare to bare. Connect the wires coming from the breaker to the other terminals on one of the outlets. Power comes in to one outlet and then to the second. If the wires are capped in the breaker box, you only need to connect the Black White and bare ones. Do this with the power off.
How do you fix garage door sensor wires?
What is wrong with them? If they are cut, simply hook back together and tape them.
Where do you hook up Black white green red for home stereo receiver hook up?
The black and white cables, or possibly black and red, are analog audio. Green is one of the three component video wires, bundled together as red green and blue. Without knowing what components you have we have no idea where you should connect these, or if it is even possible with the gear you have.
What wires do you need to connect to youtube?
you grab a battery and a jumper cable. Hook the black end up to your genitalia the other you hook up directly the monitor. Only then will you experience true High Definition.
How do you wire 2 8 ohm subwoofers to a 4 ohm amp?
Hook all the negatives together, and hook all the positives together. you would have 2 wires for each. one from the amp to the first sub, and another going from the first sub to the second.
How do I wire a Kitchen outlet?
Black wire to gold screw, white wire to silver screw, ground to green screw. If you are using a GFIC outlet then the hot wires coming in hook to the Line side of the GFIC receptacle and the wires going out to other receptacles hook to the load side.
How and where do i connect the 4 wires into the breaker box?
If your electric box has four wires in it, then it is a three phase four wire system. You should not be doing anything in this panel. It should be left to a qualified tradesman to do any work on three phase equipment.
How do you hook up your wires from your harness on a 1990 Chevy if the wires are not long enough?
Need to know what wires and which harness you speak of.
How do you hook up a garbage disposal and a dishwasher to the same outlet if the outlet has black red and white wires?
each needs a separate 20 amp feed
