0
If you have a drain available. You may need to chip some concrete around the drain to install the bottom half of the drain. With that in place, set the shower over it and the top piece screws into the drain to form a seal.
You can build a 2x4 frame and raise the shower up enough to run a drain to a sump or a floor drain.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How do you escape a stall in flight on engineering com?
you can escape a stall in flight by rapidly pressing space but you cant escape a stall unless you get the emergency booster upgrade
When my 2000 ford focus idles the motor shakes and feels like it will stall also when you accelerate the motor shakes more violently and also start to stall but then kicks in and revs up what is it?
You have a misfire - engine related, not tranny...get the engine checked/tuned up...etc... dave
What is the difference between max torque and breakdown torque of a electric motor?
Max torque and breakdown toarque are the same...,.the point at which a motor will stop/stall.
How do you drive go kart without a clutch?
Someone has to pick up the rear end and run with it, starting your engine when he drops it. (and if you spin out and stall you lose the race )
The use of a slot in the leading edge of the wing enables an airplane to land at a slower speed because it?
It allows flight at higher angles of attack, reducing stall speed.
How much does a corner shower stall cost?
The costs will vary according to the quality of the corner shower stall. However a medium quality corner shower stall would be about $6000 to buy and install.
Can you install a light fixture in a shower stall?
Yes.Have insralled many in yachts.
What tools does one need to install a handicap shower stall?
The tools that are needed to install a bathroom shower are measuring tape, spanners, tile drill, dust sheets, pencil, and pipe cutters. It is best to engage a professional shower fitter to fit one's bathroom shower, instead of DIY project.
To make your own shower stall do you need to have your drain lower?
The drain has to be slightly lower than the rest of the floor. If you tile over a cement floor, it will very gently slope down to a central drain, or a drain at the end. Try to visit some that have been done the way you want to help envision this.
How do you find square feet of shower stall?
Measure the length and width of the floor in the stall. Multiply (length) x (width). If you measured them in feet, then that's your answer. If you measured them in inches, then divide by 144, and that's your answer.
How to Install Mortar Shower Pan Membrane Liner?
How to Install Mortar Shower Pan Membrane LinerOnce you've framed the shower stall, it is time to install the pan liner and cement backer board to create a water tight seal.Remove the drain cap and tape over the drain to keep mortar and other debris from entering the drain. Put down a layer of felt paper to help prevent moisture from wicking down through to the subfloor. Place a layer of metal lathe over the felt paper. Trowel in a layer of mortar that it has a one quarter inch slope towards the drain. Once the mortar dries, place a layer of felt paper along the walls of the shower stall. Attach cement board with the rough side out along the top half of the walls. Install the shower stall membrane in the bottom of the shower so that it overlaps in the corners, covers the shower curb and is approximately six inches up the side of the walls. Cut out holes for the drain, the drain bolts and the weep holes. Seal the underside of the membrane near the drain with silicone. Nail the membrane that covers the curb only on the outside. Attach the remaining cement board leaving one inch clearance from the bottom. Caulk all seems. Place some pebbles near the weep holes to protect the openings. Trowel in a layer of mortar that has a one quarter inch slope towards the drain. Mortar the curb. Remove the tape from the drain.
Do you have to put backer board behind the tub below the shower stall area?
No you not have to put backer board behind the tub below the shower stall area. You only need to use it behind the walls of the shower stall.
How tall is a typical stall shower door?
A typical shower door is 72".
Can shower head be installed above shower stall?
You can put it at any height. Unless there is some other reason not to, something structural, I always put them above the shower stall for taller people.
What is the standard height for shower bar?
Depends which code your using ADA / barrier free design or local codes? In a shower stall figure 3' 6" - 4 feet
An architect has submitted plans for a shower stall. The client wants to know if the shower stall is shaped like an isosceles trapezoid. Which statement is true?
WXYZ is a trapezoid......
Is a shower head and taps center with the floor drain?
For aesthetic reasons, the shower head and taps are often in a line with the floor drain. I have never heard of any requirement that they must be so. It is usually most convenient to have the drain centered in the shower stall area, and the head is usually likewise centered, and a short run from the handles to the head is generally preferred, so yes, more or less.
