0
I have, I have even used the output for the input of the same amp, so that you only run one RCA cable to the amp, then run the output back to the other input, and it runs 4 channels..
:o)
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you run an amplifier off a normal car radio?
Normal car radio is no different than aftermarket. Determine the output wires on the radio, take them into the amp and the output from the amp back to the wires going to the speakers. Normal car speakers are not going to take the output of the amp if you raise it much.
What is the RCA output on a car amp for?
It is there as a "pass through". This comes in handy if your deck only has one set of RCA outputs. It enables you to "daisy chain" multiple amps together. You would run the RCA cables from the deck to amp #1's input, then use a another cable from the output on amp #1 to the input on amp #2.
How do you hook up an amp?
first you have to buy a amp hookup kit. then the long red wire in the amp kit you take the end with the fuse on it and hook it up to the battery. then you have to drill a hole in your. firewall and run the wire to the amp in the trunk of your car. then you take the big black wire and ground it to anything metal on ur car. make sure it is tight. then you take the aux cable and hook them into the back of the stereo and run the to the left or right input on the amp. Make sure that the power wire and aux cable are on opposite sides of the vehicle for less distortion and interference.then you take speaker wire and hook it up to the rear output of the amp and run it to your speaker. then you take another speaker wire and run it from the front output and run it to your rear factory speakers on the high input level. and you should be jammin down the road then.
Does a voltage regulater make the car run?
No. It controls the output of the alternator.
How do you hook up two car stereo amplifiers one to each sub in there own box can you run a power wire out of one amp over to the other amp?
Do you mean the main power from the battery or the remote turn on? If you mean the battery power, usually amp add on kits come with distributor blocks. You make one run of power wire from the battery to somewhere close to your amps. Then, hook that wire to the block, and run a new piece of wire from the block to each amp. If you mean the turn on lead, just make one run from the head unit to the first amp, and then run another piece from the first amp to the second.
If two output tubes are run in parallel and the primary impedance of the audio transformer is cut in half will a single-ended amp yield twice the output?
Yes it can if it's connected in a push pull reconfiguration
Can i use the factory amp in my 95 Lincoln town car for two twelve's?
no i have a 1993 the amp that's in there is just for the four speaker you can run a amp kit for you twelves but don't forget that wiring kit you will need to power the amp that is in there jbl
How do you put a subwoofer in your car?
You have to run the powers and grounds for the amp, do not forget to set up the remote wire either. then you will need to connect the amp to the CD player auxillary with the RCA's, then you just wire your sub to the amp.-Shocker
Can you use a 160 amp car alternator to run a 100 amp inverter?
160 amps is more than ample to run a 100 amp inverter.. what you need to look at is the required input amperage of the inverter and compare that to what's present in the circuit it's wired/plugged into. In most cases, you should be able to run up to a 400 amp inverter plugged into a 12v outlet, but again, you need to make sure.
What if my generator sends 120 volts and 65 amps into my 200 amp panel box will it run my well pump connected to a 20 amp 240 volt circuit?
No, the generator must output 220 volts which any generator I have ever seen does.
Can you run 2 80watt rms speakers Max output 600W each and 2 35watt rms speakers Max 300W each with a 60watt rms x 4 at 4 ohms Max output 700W amplifier?
Yes. Peak power or max output is rubbish. You will never get clarity at a speaker or amp's max output. RMS is what it's all about.
Can i link a powered mixer to another amp to make more volume?
There should be a "signal out" from your board. Monitor send, effects loop. Any number of outputs from a mixer you could use to run another power amp and speakers. Some power amps have a signal out line. Do not hook the speaker outputs to another amp unless you like smoke.
