Timing and Firing Orders
Ford Probe
VW Jetta
Timing Belts and Chains

Can you tell me the timing marks on a 1989 ford probe 22L GL?

222324

Top Answer
User Avatar
Wiki User
2006-05-16 16:16:26
2006-05-16 16:16:26

Timing marks? There is a timing mark on the main crankshaft pulley as well as marks on the timing belt cover to line it up with. There is also marks on the cam gear, with the #1 and that arrow being most important, as well as an arrow or other mark on the cylinder head to line it up with. All of these need to line up in order for the timing to be correct. Then the distributor can be moved left or right to fine tune the timing to spec.. -Shaun

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

where are timing marks on 89 ford probe 4 cylinder I have the bottom not the top

User Avatar

They are on the camshaft and crankshaft sprockets

User Avatar

there are no timing marks on a timing belt. the marks are on the timing gears and yes you can find the pictures needed in a workshop manuel

User Avatar

Ford Probe was created in 1989.

User Avatar

where are the timing marks on a ford ka 1.3 and how do i check the timing is correct

User Avatar

timing marks for a ford escape 2002

User Avatar

Ford doesn't use timing marks sorry

User Avatar

how to check the fluid on a manual transmission for a 1989 ford probe gt

User Avatar

Where are the timing marks on the cam gear on ford 2.9 engine

User Avatar

The timing marks for your 3.0 liter V-6 Ford Taurus can be found on the main pulley. The timing marks can also be found on the flywheel.

User Avatar

3.0 liter timing chains marks

User Avatar

The timing marks are on the timing cover for the crank pulley, and on the cyl head for the cam ...

User Avatar

The first model year of the Ford Probe ( in North America ) was ( 1989 )

User Avatar

There are no timing marks. The timing is controlled by the PCM. Power control module. It is not possible to set the timing with a timing gun.

User Avatar

if you have the exhaust manifold, oil lines, etc. from the 89 GT then yes.

User Avatar

They are on the inner timing belt cover.

User Avatar

The timing marks for a 2002 Ford Explorer are located on the timing chain and cam shaft sprocket. They must be aligned with each other to set the initial timing.

User Avatar

The timing marks on an 84 Ford Straight 6 is on the driver's side of the engine. It is above the crankshaft pulley, attached to the timing cover.

User Avatar

The 2000 Ford 4.2 engine does not have any timing marks on the crankshaft. Instead, you have to use a timing kit to install a new belt.

User Avatar

ford doesnt put timing marks on anything. u need a special cam gear alignment tool

User Avatar

The 1996 Ford 5.0 liter engine timing marks can be found on the main pulley. The timing marks will be scattered around the outside of the pulley.

User Avatar

Timing for a 1994 ford ranger with a 2.3 l

User Avatar

The timing marks are marks on the front main pulley. The marks indicate when a certain piston is at the top of its stroke. You can turn the pulley to a certain position, aligned with the timing marks, and no that piston is at the right position to set the timing.

User Avatar

The timing marks on a 1969 Ford 360 should line up between the timing chain and the cam sprocket. This sets the initial timing which can later be adjusted using a timing light.

User Avatar

what is the spark plug gap for an 1989 ford probe lx? Thank you.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.