answersLogoWhite

0


Best Answer

Yes, but be sure to install a small automatic air vent in the small tapping on the top at either end.

User Avatar

Wiki User

17y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Can you tie a cast iron radiator into a fin tube loop?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Engineering

What is a loop reactor?

A bulk (slurry) polymerisation reactor which is made of a closed long tube through which the slurry is circulated. Loop reactors are characterised by a very narrow residence time distribution, leading to uniform product characteristics.


Is the propeller shaft the same as the stern tube shaft?

The propeller shaft in a boat engine is fastened to the flywheel by bolts, and it passes through the boat's thrust block and is aligned with the shaft tunnel. It also passes through the stern tube to drive the propeller. The stern tube shaft itself holds the "prop" shaft in place and shut off the open end when it pierces the aft hull. It is commonly manufactured as cast iron and welded into the frame of the stern of the ship.


Heat exchangers can be found in what systems?

furnance Applications of finned tube heat exchangers embody Steam air heater / steam radiator, energy fluid air heater / energy fluid radiator, predicament air heater / predicament radiator, Air heater for spray dryers, Air heater for fluid bed dryer, Air heater for flash dryers and Air heater for dryers. These area unit factory-made exploitation high grade steel, stainless-steel, copper, brass and metal. Our Finned Tube Heat exchangers area unit designed to satisfy the particular temperature, heavy duty condition and pressure of the fluids. Fin tubes,tubos aletados, acero inoxidable, Stainless Steel 304, Aluminum,Finned tube,Brass tube, Valve & Pipe Fitting Supplier at http://www.ts-aceroinoxidable.com


What is difference between tube connector and tube adapter fitting?

A tube connector is the standard fitting that goes on a tube or hose. A tube adapter fits to a tube or hose and enables it to connect to a fitting of a different size to its standard.


Which is better fire tube boiler or water tube boiler?

The words are literal , a water tube boiler is water inside the tubes with hot gases surrounding them and a fire tube boiler are got gases within the tubes with water surrounding them.

Related questions

Where is the thermostat in 1997 Buick Century?

Follow the upper radiator hose from the radiator. It will attach to a cast iron tube that is mounted to the engine. The Thermostat is located at the base of the tube that goes into the engine. You will need to remoe the air sensing unit to be able to detach the cast irom tube and remove the thermostat. there are two bolts that attach the cast iron tube to the engine (I think they are 10mm). The front one is easy to get at (use a speed socket wrench. The back one is more difficult. You will need a long handle closed wrench. Once you detach the tube, you will find the Thermostat sitting inside. From Tiger


What happens to iron placed in a test tube with a stopper?

Iron and oxygen in a test tube alone will not react (observed by placing a piece of iron in a test tube with a stopper).Iron and water in a test tube alone will not react (observed by completely submerging a piece of iron in water in a test tube with a stopper).Iron, water and oxygen in a test tube will react (observed by placing a piece of iron in a test tube and submerging half of it with water). The following reaction will take place: iron + water + oxygen ----> hydrated iron(III) oxide. Hydrated iron(III) oxide is the chemical name for rust, which will appear as orange flaking on the piece of iron. To speed up this reaction you can use a bit of salt as a catalyst.


What line is parliament tube station?

In Melbourne, Vic - on the City Loop


Where is the thermostat in 98 Civic EX Coupe?

The thermostat should be located in a metal tube that runs behind the cylinder block. Follow the bottom radiator hose to the metal tube. It should be near the distributor, but lower and in the back more, but just follow the radiator tube and you'll find it. Drain your coolant and take off your radiator tube. Where the radiator tube connects to, look at it, it should have three to two small 10mm bolt that holds it on the metal tube. Take that it off and the thermostat should be in there.


Where is the thermostat located on a 1998 Honda Civic EX?

The thermostat should be located in a metal tube that runs behind the cylinder block. Follow the bottom radiator hose to the metal tube. It should be near the distributor, but lower and in the back more, but just follow the radiator tube and you'll find it. Drain your coolant and take off your radiator tube. Where the radiator tube connects to, look at it, it should have three to two small 10mm bolt that holds it on the metal tube. Take that it off and the thermostat should be in there....


Where is the top radiator tube located in a 1999 Oldsmobile cutlass?

You fill the radiator through the overflow tank.


Where is the orifice tube 04 cavalier?

passanger side of radiator. inside the aluminum tube. has a nut on it to take apart for the orifice tube


Why is loop flamed before it is placed in a culture tube?

To kill any bacteria on it.


What were medieval cannons built from?

The earliest European cannon were made of iron bars welded together around a mandrel to form a tube. One end was welded shut with a plug or left open for a breechblock. The tube had iron bands welded around it. Later cannon were cast from bronze.


Why did you use an inoculating loop instead of a needle to make the transfers from the culture plates to the culture tubes?

A inoculating loop is used for transfers from culture plates to culture tubes instead of the inoculating needle because the needle could puncture the agar in tube. The loop is much easier as well to get liquid amount into the tube.


My 95' Tahoe is overheating and steam is blowing out of the front-end around a tube that inserts into the radiator. What should I do?

You might need to either replace your thermostat or the radiator itself. I can't tell what "tube" you're talking about, but it COULD just be the radiator cap that's bad and you're venting into the tube that goes to the coolant recovery reservoir. If that's the case, just get a new radiator cap. If the radiator hose is leaking, replace it. Unfortunately, I can't tell what's wrong from your description.


What color tube for total iron binding capacity?

Marble top (SST) tube