0
Lookup both vehicles below in sources and related links and note the size and part numbers of the wipers. If the same yes. If not; then no.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What size windshield wiper blade for an 1999 Infinity I30?
The 1999 Infinity I30 takes a 22" driver side wiper blade and a 21" passenger side wiper blade. However, when buying windshield wiper blades be sure to always use the application guide book at the store
What is windshield wiper blade?
a windshield wiper blade is somthing you use to wash your windows on cars so that the windows look very clean instead of just leaving them dirty
What is the rear wiper blade size on a 2002 Jeep Liberty?
The wiper blade is an 11". DO NOT BUY BOSCH 11" wiper blades for a replacement, unless you plan on using your old adapter fitting with the new blade....Bosch does NOT have the adapter to fit your blade, and if you break the original adapter, you cannot use the Bosch blade. I learned this the hard way. I believe that Anco makes an 11" blade that will fit the Jeep Liberty 2002-2004.
How do you change the windshield wiper blade on a 1976 dodge eldorado motorhome?
Use a screw driver to pry up on the center of the wiper blade where that pin goes through, and it will slide off the pin. Then simply snap the new one on.
What size wiper blade does your 2003 Taurus use?
passenger side 20 driver side 24
What is the length of a 2001 Acura MDX rear wiper blade?
Length is not an issue because its a special wiper blade assembly that you must go to the dealer to purchase. Unfortuantely Acura didn't use one of the 13 common rear wiper blade designs where aftermarket are available. The front wipers are available aftermarket however. See sources and related links below.
How do you change blade?
See Related Links Below For Wiper Blade Installation VideosRemoving wipers on most vehicles will be one of these procedures: If your wiper arm has a pin end: insert a flat blade screwdriver between the arm and the wiper blade and twist the screwdriver; the blade will pop off. Simply push the new blade on until it clicks. If your wiper arm has a hook end: Lift the arm/blade off the windshield, tip the top edge of the blade up toward you, and pull back on the blade until it releases. Some of these hook type can be stubborn so you might need to use some moderate force to remove them. Install the new blade by pushing it up into the hook until it clicks. I have personally installed THOUSANDS of pairs of wiper blades and still get frustrated when I do some of them, so Don't think you are doing it wrong ;some just get stuck on!
What size is the windshield wiper blade for a Mazda miata?
1990-2005 Mazda Miatas use 18" wiper blades on both the driver and passenger side wipers.
Can you change just the blade in windshield wiper on a Nissan Maxima?
I'm going with the assumption that this question is asking about what are commonly called the rubber blade refill inserts rather than the wiper blade which is everything attached to the wiper arm; blade and frame. Most likely yes - you can just replace the rubber insert however in most cases I don't recommend it, especially if you live in cold winter weather climates which puts a lot of stress on the entire wiper blade or you live in a climate where you use your wipers quite a bit. The difference in price, mechanical skill (and patience) between installing refill inserts and full wiper blades is relatively small. If you replace the whole wiper blade, its cheap insurance that your blades will perform better when you most need them.
How do you change wiper blades on a Chevrolet?
See Sources and Related Links Below For Wiper Blade Installation VideosRemoving wipers on most vehicles will be one of these procedures: If your wiper arm has a pin end: insert a flat blade screwdriver between the arm and the wiper blade and twist the screwdriver; the blade will pop off. Simply push the new blade on until it clicks. If your wiper arm has a hook end: Lift the arm/blade off the windshield, tip the top edge of the blade up toward you, and pull back on the blade until it releases. Some of these hook type can be stubborn so you might need to use some moderate force to remove them. Install the new blade by pushing it up into the hook until it clicks. I have personally installed THOUSANDS of pairs of wiper blades and still get frustrated when I do some of them, so Don't think you are doing it wrong ;some just get stuck on!
How do you replace a Toyota Camry windshield wiper?
I have no idea. I have tried everything short of using an acetylene torch. I can see a little tab on the windshield wiper where it connects to the arm, however, I cannot get it to release. At least I think it's a tab. I am going to call the dealership and I'll let you know what I find out. How to replace the wiper blades (on a 2001 Camry): Pull the wiper arm away from the home position and lock into the service position. (With the ignition on, run the wipers into the upright position and turn the ignition off. Lift the wiper blade up (vertical) off the windshield.) Turn the blade at an angle from the wiper arm (rotate the wiper blade counterclockwise (up)). You'll see (under the joint) a flat piece of steel -- actually the end of a flat spring. Push this lock spring with a screwdriver or a pencil eraser toward the joint to release the blade, then pull the wiper blade down (toward the windshield) to remove it from the arm. Attach (in reverse) the new wiper to the wiper arm and press it into place until you hear a click. Note: In most new cars the driver side wiper blade is longer than the passenger so make sure you buy the correct blades. My driver side wiper is 21", my passenger is 19". This worked for my 1990 Toyota Camry. Step 1, obtain new wiper blades. Waste no time and swallow your pride. Go into the auto parts store to the information desk and let one of the ten year olds who work there look it up for you on a computer and help you find it. Step 2, replace wipers. It took two seconds to replace the wipers and two hours to figure out how to replace them. Ignore the pictorial directions on the Bosch package, which are a) unintelligible and b) a set of parallel instructions for removing and attaching every conceivable type of wiper blade, not a single set of instructions to be followed. You will not be using everything in the package (adapter, screws), just the new wiper blade and the shiny metal pin. If for some reason you don't have a shiny metal pin (one of my packages didn't have one), don't worry, you can use the pins currently on your car. The wiper arm has a piece on the end held on by two screws (we shall call this by the technical term, "the piece on the end"). A metal pin goes through this into the wiper blade and holds the blade on. Lift the wiper arm straight up (gently) into what they call "the service position" so you can see it properly. There is a little tab on the piece on the end. If you press this you can pop the pin out and the blade right off (and then the pin comes out altogether). Carefully lay the removed blade down on the hood so that you can remember the proper orientation. Take the new Bosch blade, orient it the same way, check to make sure it is the right length (driver's side is longer than passenger's side), stick the pin through the piece on the end and the new blade just the way it was on the old one. Push until you hear it click. Lay the wiper blade back down. That's it. Really.
How do you get the original windshield wipers off of a '93 Pontiac Grand Am so you can change the blades?
There is a small spring slot in the middle of the top ot the wiper blade. Use a slot screwdriver to push the spring down and the wiper blade will pop off.
